TP-Link manual TL-WR941ND Wireless N Router

Page 47

¾Mode - Select the desired mode. The default setting is 11bgn mixed.

TL-WR941NDWireless N Router

¾Mode - Select the desired mode. The default setting is 11bgn mixed.

11b only - Select if all of your wireless clients are 802.11b.

11g only - Select if all of your wireless clients are 802.11g.

11n only- Select only if all of your wireless clients are 802.11n.

11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.

Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can connect to the Router. When 802.11n mode is selected, only 802.11n wireless stations can connect to the AP. It is strongly recommended that you set the Mode to 802.11b&g&n, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the Router.

¾Channel width - Select any channel width from the pull-down list. The default setting is automatic, which can adjust the channel width for your clients automatically.

) Note:

If 11b only, 11g only, or 11bg mixed is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed.

¾Max Tx Rate - You can limit the maximum tx rate of the Router through this field.

¾Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access.

¾Enable SSID Broadcast - When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. If you select the Enable SSID Broadcast checkbox, the Wireless Router will broadcast its name (SSID) on the air.

¾Enable WDS - Check this box to enable WDS. With this function, the Router can bridge two or more WLANs. If this checkbox is selected, you will have to set the following parameters as shown below. Make sure the following settings are correct

¾SSID(to be bridged) - The SSID of the AP your Router is going to connect to as a client. You can also use the search function to select the SSID to join.

¾BSSID(to be bridged) - The BSSID of the AP your Router is going to connect to as a client. You can also use the search function to select the BSSID to join.

¾Survey - Click this button, you can search the AP which runs in the current channel.

-38-

Image 47

Contents Rev 1.1.0 TL-WR941ND Wireless N RouterFCC STATEMENT COPYRIGHT & TRADEMARKSCountry FCC RF Radiation Exposure StatementCE Mark Warning National restrictionsNCC Notice Industry Canada StatementKorea Warning Statements Page EN 550241998+A12001+A22003 EN 61000-3-22006+A12009+A22009 EN DECLARATION OF CONFORMITYETSI EN 300 328 ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN 550222006 +A12007Chapter CONTENTSPackage Contents DHCP 4.15.2 TL-WR941ND Wireless N Router Package Contents1.1 Overview of the Router Flexible Access ControlSimple Installation Chapter 1.Introduction1.3 Main Features Status 1.4 Panel Layout1.4.1 The Front Panel Name1.4.2 The Rear Panel ¾ RESET2.1 System Requirements Chapter 2.Connecting the Router2.2 Installation Environment Requirements 2.3 Connecting the RouterFigure 2-1 Hardware Installation of the TL-WR941ND Wireless N Router 3.1 TCP/IP Configuration Chapter 3.Quick Installation Guide1. Is the connection between your PC and the Router correct? Please check the connection following these stepsFigure 3-1 Success result of Ping command Figure 3-2 Failure result of Ping command3.2 Quick Installation Guide Figure 3-6 Choose WAN Connection Type Figure 3-5 Quick SetupFigure 3-8 Quick Setup - MAC Clone Figure 3-7 Quick Setup - PPPoEFigure 3-10 Quick Setup - Static IP Figure 3-9 Quick Setup - MAC CloneNote Dialog ¾ WPA/WPA2-Personal - Select WPA based on pre-shared passphrase 4.6 WirelessFigure 3-13 Quick Setup - Finish 4.2 Status Chapter 4.Configuring the Router4.1 Login Figure 4-1 Router Status 4.3 Quick SetupPlease refer to 3.2 Quick Installation Guide 4.4 QSSMethod One I. By PBCMethod Two The QSS Configuration Screen of Wireless Adapter Method ThreeTL-WR941ND Wireless N Router II. By PIN Method Two Enter the PIN from my Router added to the network 4.5 Network4.5.1 WAN Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE Figure 4-8 PPPoE Advanced Settings NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au Figure 4-10 L2TP Settings Figure 4-11 PPTP Settings z Static IP - Connections which use static IP address assignment z Dynamic IP - Connections which use dynamic IP address assignmentFigure 4-13 MAC Address Clone 4.5.2 LAN4.5.3 MAC Clone Figure 4-12 LANOnly the PC on your LAN can use the MAC Address Clone function 4.6 Wireless4.6.1 Wireless Settings Figure 4-15 Wireless Settings ¾ Mode - Select the desired mode. The default setting is 11bgn mixed 4.6.2 Wireless Security ¾ WPA /WPA2 - Enterprise - It’s based on Radius Server Encryption - You can select either Automatic, or TKIP or AES Figure 4-20 Wireless MAC address Filtering 4.6.3 Wireless MAC Filtering4. Click the Save button to save this entry to access for Filtering Rules 4.6.4 Wireless Advanced4.6.5 Wireless Statistics This page will be refreshed automatically every 5 seconds 4.7.1 DHCP Settings4.7 DHCP ¾ Default Domain - Optional. Input the domain name of your network 4.7.3 Address Reservation 4.7.2 DHCP Clients ListTo modify or delete an existing entry 4.8 ForwardingTo Reserve IP addresses 4.8.1 Virtual Servers To set up a virtual server entryFigure 4-31 Add or Modify a Virtual Server Entry 4.8.2 Port TriggeringTo add a new rule, follow the steps below 3. Incoming Port Range cannot overlap each other 4.8.3 DMZTo assign a computer or server to be a DMZ server 4.8.4 UPnP4.9.1 Basic Security 4.9 Securityz z z Figure 4-37 Basic Security4.9.2 Advanced Security 4.9.3 Local Management Figure 4-39 Local Management 4.9.4 Remote ManagementFigure 4-40 Remote Management 4.10Parental ControlTo add a new entry, please follow the steps below 7. Click the Save button 4.11.1 Rule 4.11Access ControlFigure 4-45 Access Control Rule Management To add a new rule, please follow the steps belowFigure 4-46 Add or Modify Internet Access Control Entry Figure 4-47 Host Settings 4.11.2 HostFigure 4-49 Add or Modify a Host Entry Figure 4-48 Add or Modify a Host EntryFigure 4-50 Target Settings 4.11.3 TargetFigure 4-52 Add or Modify an Access Target Entry Figure 4-51 Add or Modify an Access Target EntryTo add a new schedule, follow the steps below 4.11.4 ScheduleFigure 4-55 Advanced Routing 4.12 Advanced RoutingFigure 4-54 Advanced Schedule Settings To add static routing entries Other configurations for the entries4.12.1 Static Routing List 4.12.2 System Routing Table 4.13Bandwidth Control4.13.2 Rules List 4.13.1 Control SettingsTo add/modify a Bandwidth Control rule, follow the steps below 4.14IP & MAC Binding Setting4.14.1 Binding Setting Figure 4-64 Binding Setting To add IP & MAC Binding entries, follow the steps belowTo modify or delete an existing entry, follow the steps below To find an existing entry, follow the steps belowFigure 4-67 ARP List 4.14.2 ARP ListFigure 4-66 Find IP & MAC Binding Entry 4.15.1 Comexe.cn DDNS 4.15Dynamic DNS4.15.2 Dyndns.org DDNS To set up for DDNS, follow these instructionsFigure 4-69 Dyndns.org DDNS Settings 4.15.3 No-ip.com DDNSFigure 4-71 The System Tools menu 4.16System ToolsFigure 4-70 No-ip.com DDNS Settings To set time manually 4.16.1 Time Settings2. The time will be lost if the router is turned off 4.16.2 DiagnosticTo set time automatically To set Daylight SavingFigure 4-73 Diagnostic Tools To upgrade the Routers firmware, follow these instructions below 4.16.3 Firmware Upgrade4. The Router will reboot after the upgrading has been finished 4.16.4 Factory Defaults4.16.5 Backup & Restore 4.16.6 Reboot 4.16.8 System Log 4.16.7 PasswordFigure 4-80 System Log Figure 4-81 Mail Account Settings Figure 4-82 Statistics 4.16.9 StatisticsStatistics Table Wireless N RouterTL-WR941ND 1. How do I configure the Router to access Internet by ADSL users? Appendix A FAQFigure A-4 Virtual Servers 3. I want to use Netmeeting, what do I need to do?Figure A-3 MAC Clone Figure A-6 DMZ Figure A-5 Add or Modify a Virtual server Entry4. I want to build a WEB Server on the LAN, what should I do? field of the Web browser 5. The wireless stations cannot connect to the Router1. Install TCP/IP component Appendix B Configuring the PCsFigure B-2 ¾ Setting IP address automaticallyNow you have two ways to configure the TCP/IP protocol below shown in the Figure belowFigure B-3 ¾ Setting IP address manuallyFigure B-4 Environmental and Physical Appendix C SpecificationsWireless GeneralAppendix D Glossary identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name

Related manuals

Manual 76 pages 42.16 Kb