TP-Link manual 4.11Access Control, Rule, TL-WR941ND Wireless N Router

Page 72

4.11Access Control

TL-WR941NDWireless N Router

3.Click “Parental Control” menu on the left to go back to the Add or Modify Parental Control Entry page:

zClick Add New... button.

zEnter 00-11-22-33-44-AA in the MAC Address of Child PC field.

zEnter “Allow Google” in the Website Description field.

zEnter “www.google.com” in the Allowed Domain Name field.

zSelect “Schedule_1” you create just now from the Effective Time drop-down list.

zIn Status field, select Enable.

4.Click Save to complete the settings.

Then you will go back to the Parental Control Settings page and see the following list, as shown in Figure 4-43.

Figure 4-43 Parental Control Settings

4.11Access Control

Figure 4-44 Access Control

There are four submenus under the Access Control menu as shown in Figure 4-44:Rule, Host, Target and Schedule. Click any of them, and you will be able to configure the corresponding function.

4.11.1 Rule

Choose menu “Access Control → Rule”, you can view and set Access Control rules in the screen as shown in Figure 4-45.

-63-

Image 72

Contents TL-WR941ND Wireless N Router Rev 1.1.0COPYRIGHT & TRADEMARKS FCC STATEMENTFCC RF Radiation Exposure Statement CE Mark WarningNational restrictions CountryIndustry Canada Statement Korea Warning StatementsNCC Notice Page DECLARATION OF CONFORMITY ETSI EN 300 328ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN 550222006 +A12007 EN 550241998+A12001+A22003 EN 61000-3-22006+A12009+A22009 ENCONTENTS Package ContentsChapter DHCP 4.15.2 Package Contents TL-WR941ND Wireless N RouterFlexible Access Control Simple InstallationChapter 1.Introduction 1.1 Overview of the Router1.3 Main Features 1.4 Panel Layout 1.4.1 The Front PanelName Status¾ RESET 1.4.2 The Rear PanelChapter 2.Connecting the Router 2.2 Installation Environment Requirements2.3 Connecting the Router 2.1 System RequirementsFigure 2-1 Hardware Installation of the TL-WR941ND Wireless N Router Chapter 3.Quick Installation Guide 3.1 TCP/IP ConfigurationPlease check the connection following these steps Figure 3-1 Success result of Ping commandFigure 3-2 Failure result of Ping command 1. Is the connection between your PC and the Router correct?3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-6 Choose WAN Connection TypeFigure 3-7 Quick Setup - PPPoE Figure 3-8 Quick Setup - MAC CloneFigure 3-9 Quick Setup - MAC Clone Figure 3-10 Quick Setup - Static IPNote Dialog 4.6 Wireless ¾ WPA/WPA2-Personal - Select WPA based on pre-shared passphraseFigure 3-13 Quick Setup - Finish Chapter 4.Configuring the Router 4.1 Login4.2 Status 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide4.4 QSS Figure 4-1 Router StatusI. By PBC Method OneMethod Two Method Three The QSS Configuration Screen of Wireless AdapterTL-WR941ND Wireless N Router II. By PIN Method Two Enter the PIN from my Router 4.5 Network 4.5.1 WANadded to the network Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE Figure 4-8 PPPoE Advanced Settings NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au Figure 4-10 L2TP Settings Figure 4-11 PPTP Settings z Dynamic IP - Connections which use dynamic IP address assignment z Static IP - Connections which use static IP address assignment4.5.2 LAN 4.5.3 MAC CloneFigure 4-12 LAN Figure 4-13 MAC Address Clone4.6 Wireless 4.6.1 Wireless SettingsOnly the PC on your LAN can use the MAC Address Clone function Figure 4-15 Wireless Settings ¾ Mode - Select the desired mode. The default setting is 11bgn mixed 4.6.2 Wireless Security ¾ WPA /WPA2 - Enterprise - It’s based on Radius Server Encryption - You can select either Automatic, or TKIP or AES 4.6.3 Wireless MAC Filtering Figure 4-20 Wireless MAC address Filtering4. Click the Save button to save this entry 4.6.4 Wireless Advanced to access for Filtering Rules4.6.5 Wireless Statistics 4.7.1 DHCP Settings 4.7 DHCPThis page will be refreshed automatically every 5 seconds ¾ Default Domain - Optional. Input the domain name of your network 4.7.2 DHCP Clients List 4.7.3 Address Reservation4.8 Forwarding To Reserve IP addressesTo modify or delete an existing entry To set up a virtual server entry 4.8.1 Virtual Servers4.8.2 Port Triggering Figure 4-31 Add or Modify a Virtual Server EntryTo add a new rule, follow the steps below 4.8.3 DMZ 3. Incoming Port Range cannot overlap each other4.8.4 UPnP To assign a computer or server to be a DMZ server4.9 Security 4.9.1 Basic SecurityFigure 4-37 Basic Security z z z4.9.2 Advanced Security 4.9.3 Local Management 4.9.4 Remote Management Figure 4-39 Local Management4.10Parental Control Figure 4-40 Remote ManagementTo add a new entry, please follow the steps below 7. Click the Save button 4.11Access Control 4.11.1 RuleTo add a new rule, please follow the steps below Figure 4-45 Access Control Rule ManagementFigure 4-46 Add or Modify Internet Access Control Entry 4.11.2 Host Figure 4-47 Host SettingsFigure 4-48 Add or Modify a Host Entry Figure 4-49 Add or Modify a Host Entry4.11.3 Target Figure 4-50 Target SettingsFigure 4-51 Add or Modify an Access Target Entry Figure 4-52 Add or Modify an Access Target Entry4.11.4 Schedule To add a new schedule, follow the steps below4.12 Advanced Routing Figure 4-54 Advanced Schedule SettingsFigure 4-55 Advanced Routing Other configurations for the entries 4.12.1 Static Routing ListTo add static routing entries 4.13Bandwidth Control 4.12.2 System Routing Table4.13.1 Control Settings 4.13.2 Rules List4.14IP & MAC Binding Setting 4.14.1 Binding SettingTo add/modify a Bandwidth Control rule, follow the steps below To add IP & MAC Binding entries, follow the steps below To modify or delete an existing entry, follow the steps belowTo find an existing entry, follow the steps below Figure 4-64 Binding Setting4.14.2 ARP List Figure 4-66 Find IP & MAC Binding EntryFigure 4-67 ARP List 4.15Dynamic DNS 4.15.1 Comexe.cn DDNSTo set up for DDNS, follow these instructions 4.15.2 Dyndns.org DDNS4.15.3 No-ip.com DDNS Figure 4-69 Dyndns.org DDNS Settings4.16System Tools Figure 4-70 No-ip.com DDNS SettingsFigure 4-71 The System Tools menu 4.16.1 Time Settings To set time manually4.16.2 Diagnostic To set time automaticallyTo set Daylight Saving 2. The time will be lost if the router is turned offFigure 4-73 Diagnostic Tools 4.16.3 Firmware Upgrade To upgrade the Routers firmware, follow these instructions below4.16.4 Factory Defaults 4.16.5 Backup & Restore4. The Router will reboot after the upgrading has been finished 4.16.6 Reboot 4.16.7 Password 4.16.8 System LogFigure 4-80 System Log Figure 4-81 Mail Account Settings 4.16.9 Statistics Figure 4-82 StatisticsWireless N Router TL-WR941NDStatistics Table Appendix A FAQ 1. How do I configure the Router to access Internet by ADSL users?3. I want to use Netmeeting, what do I need to do? Figure A-3 MAC CloneFigure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry Figure A-6 DMZ4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the Router field of the Web browserAppendix B Configuring the PCs 1. Install TCP/IP component¾ Setting IP address automatically Now you have two ways to configure the TCP/IP protocol belowshown in the Figure below Figure B-2¾ Setting IP address manually Figure B-3Figure B-4 Appendix C Specifications WirelessGeneral Environmental and PhysicalAppendix D Glossary identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name

Related manuals

Manual 76 pages 42.16 Kb