TP-Link td-w8951nd manual TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide

Page 39

TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide

¾Access point Settings: These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network.

•Access point: Select Activated to allow wireless station to associate with the access point.

•Channel: Select your region and the channel you want to use from the drop-down List of Channel. This field determines which operating frequency will be used. It is not necessary to change the default channel unless you notice interference problems with another nearby access point.

•Transmit Power: Here you can specify the transmit power of modem router. You can select High, Medium or Low which you would like. High is the default setting and is recommended.

•Beacon Interval: Enter a value between 20-1000 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the modem router to synchronize the wireless network. The default value is 100.

•RTS/CTS Threshold: Should you encounter inconsistent data flow, only minor reduction of the default value 2347 is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The modem router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. In most cases, keep its default value of 2347.

•Fragmentation Threshold: This value specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.

•DTIM: This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the modem router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1.

•Wireless Mode: In the drop-down list you can select “802.11b”, “802.11g”, “802.11n”, “802.11b+g”, “802.11g+n” and “802.11b+g+n”. “802.11b+g+n” allows 802.11b, 802.11g and 802.11n wireless stations to connect to the modem router.

31

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Rev 4.0.0 TD-W8951ND 150Mbps Wireless N ADSL2+ Modem RouterCopyright & Trademarks FCC Statement Korea Warning Statements NCC Notice & Bsmi Notice Yang Hongliang Product Manager of International Business Product Description 150Mbps Wireless N ADSL2+ Modem RouterContents Maintenance Package Contents Main Features WirelessProduct Overview Conventions LED Explanation Name Status Indication Front PanelBack Panel Installation Environment Wall-mount Install Connecting the Modem RouterTD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Configure PC Quick Installation GuideTD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Configure the IP address as -4shows. After that, click OK Is the TCP/IP configuration for your PC correct? LoginTD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Click Next to finish the Quick Start Device Info StatusSystem Log Statistics Receive Receive total Bytes Statistics TableQuick Start Internet Interface SetupTD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Dynamic IP Address Static IP Address PPPoA/PPPoE 2 LAN Bridge ModeTD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Wireless TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide WEP-128Bits WEP-64BitsWPA2-PSK WPS Settings PBCMethod One Method Two PIN code 22 Method One Enter the PIN into my modem router Start WPSTD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Firewall Advanced SetupRouting 3 NAT Virtual Server 3.1 DMZOther operations for the entries as shown in Figure To add a virtual server entryTo add a mapping rule 4 QoS TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Vlan Assign Vlan Pvid for each Interface Define Vlan Group Adsl 1 ACL Access ManagementIP Filter FilterTD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide To add an IP Address filtering entry TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide To add a MAC Address filtering entry TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide To add a URL filter entry 2.4 URLUPnP SnmpDdns Cwmp Maintenance AdministrationTime Zone PC’s Clock NTP Server automaticallyManually FirmwareTo back up the modem router’s current settings To restore the modem router’s settings SysRestart DiagnosticsHelp TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Physical and Environment GeneralT2. What can I do if I don’t know or forget my password? Appendix B TroubleshootingClick Network Connections Connection Click PropertiesProtocol TCP/IP Click OK TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Area Connection Click Properties TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Click Internet Options Select Never dial a connection T4. What can I do if I cannot access the Internet?TD-W8951ND150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix C Technical Support
Top Page Image Contents