Dukane 8802, 8062 manual Lamp, Do not use the projector with the lamp cover removed

Page 26

THE LAMP

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately: DT00511), then contact your local dealer. Before replacing the lamp, turn off the power, and unplug the power cord, then wait at least 45 minutes, in order to ensure that the lamp is properly cooled. Removing the lamp bulb while it is still hot could cause burns, or cause the lamp bulb to burst.

The LCD projector uses a glass lamp bulb. It is a mercury lamp with high WARNING internal pressure. High-pressure mercury lamps can break with a loud

bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

•Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

•If the replace lamp indicator (see "Related Messages" (Vol.2 7 ) and "Regarding the

indicator Lamps" (Vol.2 8 )) comes on, replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

•If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer.

•If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

•If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

•Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.

•Do not use the projector with the lamp cover removed.

25

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Models 8062/8802 Contents Soft carrying case Remote control Projector FeaturesPower cord US Type UK Type Europe Type Projector With Lens CapPower cord Only use the power cord that came with the projectorDevices you will be using to the projector Part Names ReferencePosition button Auto button Blank button Volume button Mute buttonFreeze button Keyboard buttons Cursor buttonsSetting UP the Projector Adjusting the Projectors Elevator FeetTop view Side view Adjusting the Screen Size and Projection DistanceScreen Connecting Your Devices Ports and Cables Function Projector Port Connection CablesConnecting Your Devices Connecting to a ComputerConnecting to a DVD Player Connecting to a VCRConnecting to a Display Monitor Operating the remote control Using the Remote ControlPutting batteries into the remote control unit Turning on the Power Selecting an Input Signal Turning OFF the Power Press Buttons to adjust Volume Adjusting the VolumePress the Volume button Temporarily Muting the SoundPress the Position button Adjusting the PositionUse Buttons to adjust Position Automatic Adjustment for Video Input Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Press the Auto buttonAs illustrated on the right, a dialog will appear Correcting Keystone DistortionsPress the Keystone button On the screen to aid you in correcting the distortionUsing the Magnify Feature Freezing the ScreenTemporarily Blanking the Screen Signal SearchingSelecting the Aspect Ratio Select an item using Buttons, then press Or Enter button Using the Menu FunctionsSelect a menu using Buttons Then press Or Enter button Press Buttons to adjust the levelAvailable Functions Remote Control Operation Operating the PC ScreenDo not use the projector with the lamp cover removed High Voltage High Temperature High PressureLamp Replacing the lamp AIR Filter Caring for the air filterReplacing the air filter Caring for the inside of the projector Caring for the cabinet and remote control transmitterOther Care Caring for the lensFor Technical see the end of this manual Main Menu Multifunctional SettingsMain Menu PICTURE1 Menu Picture 1 MenuPicture 2 Menu PICTURE2 MenuAuto Input MenuInput Menu VideoBlank Screen MenuScreen Menu Start UPOption Menu VolumeOption Menu Auto OFFRelated Messages Regarding the Indicator Lamps Power Lamp TempVol.2-3 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-6Specification SpecificationsDimension Diagram Unit mmWarranty and AFTER-SERVICE RGB in 1/2 Signal Connector PIN AssignmentSignal Terminal Specification Sub 15-pin ShrinkExample of Computer Signal Resolution FH kHz FV Hz Rating Signal mode Display modeInitial SET Signals Serial Mouse Connection to the Mouse ControlADB Mouse USB MouseRS-232C Communication Command dataConsist of header 7 bytes + command data 6 bytes ProtocolUsing the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCommand data chart 日本語Be EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices Page Page Page Page Page Page Dukane Corporation 401-8062/8802 Audio Visual Products

8062, 8802 specifications

The Dukane 8802 and 8062 ultrasonic welding systems represent a significant advancement in the field of ultrasonic technology, designed for precision joining of thermoplastics and metals. These systems combine innovative engineering with user-friendly features, making them an ideal choice for various industrial applications.

One of the defining features of the Dukane 8802 and 8062 is their robust ultrasonic generator that provides consistent power output. This ensures that every weld is reliable and repeatable, crucial for high-volume production environments. The systems utilize a patented Smart Generator technology, capable of automatically tuning to the optimal frequency, thus maximizing efficiency and enhancing acoustic performance.

Both models are equipped with a high-performance ultrasonic transducer, which converts electrical energy into mechanical energy. This transducer is designed for durability and long-term performance, ensuring minimal downtime and reduced maintenance needs. The systems also feature advanced piezoelectric materials that enhance energy conversion, leading to superior welding results.

User convenience is paramount, reflected in the digital touchscreen interface that allows operators to easily set parameters, monitor real-time performance, and adjust settings as necessary. Multiple welding modes are available, including time, energy, and distance control, allowing users to select the best approach according to their specific application needs.

The Dukane 8802 and 8062 also incorporate a lightweight and ergonomic design, facilitating easy integration into existing production lines. The adjustable horn and fixture options offer versatility in handling different component shapes and sizes, making these systems suitable for a wide range of industries including automotive, medical, and consumer goods.

Moreover, both systems emphasize safety and compliance, featuring built-in sensors that prevent overload conditions and ensure weld quality. This focus on safety enhances operator confidence and protects expensive tooling.

In conclusion, the Dukane 8802 and 8062 ultrasonic welding systems stand out due to their advanced technology, efficiency, and operator-friendly design. These characteristics not only improve manufacturing processes but also contribute to cost savings and higher quality standards across various applications.
Top Page Image Contents