Dukane 8062, 8802 manual Dukane Corporation

Page 59

DUKANE CORPORATION

FIVE-YEAR LIMITED WARRANTY

This Dukane projector is warranted to the original purchaser for a period of five (5) years from the original purchase date – in normal operating conditions – against defects in material and workmanship . DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

DURING THE WARRANTY PERIOD, DUKANE CORPORATION’S LIABILITY FOR ANY DEFECTIVE PRODUCT (except for the lamp, which is subject to whatever warranties the manufacturer may provide) IS LIMITED TO THE REPAIR OR REPLACEMENT OF PRODUCT AT DUKANE CORPORATION’S OPTION. REPLACEMENT PRODUCTS MAY BE NEW OR USED (used units will not exceed hours of defective unit). The following are not covered by the limited warranty and Dukane Corporation shall not be liable for:

1.Any product which is not distributed in the U.S.A. or Canada by Dukane Corporation or an authorized dealer.

2.Normal decrease in lamp light output over time.

3.Damage, deterioration or malfunction resulting from:

∙Accident, misuse, abuse, neglect, improper ventilation, fire, dust, smoke, water, lighting or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product (including proper maintenance of air filters).

∙Repair or attempted repair by anyone other than a Dukane Corporation authorized service center.

∙Any shipment of product (claims must be presented to the carrier).

∙Removal or installation of the product.

∙Any other causes which do not relate to a product defect.

∙Use of the product beyond normal operating conditions. Normal operating conditions are defined as product use not in excess of 8 hours per day and 260 days per year.

4.Cartons, carry cases, shipping cases, batteries, or any accessories used in connection with the product.

5.Service required as a result of third party components.

6.Product used as commercial rental units

Dukane corporation will pay labor and material expenses for covered items, but Dukane Corporation will not pay for the following:

1.Removal or installation charges.

2.Cost of technical adjustment, set-up, maintenance, or adjustment of user controls.

3.Payment of shipping and related charges incurred in returning the product for warranty repair.

Dukane Corporation disclaims all liability for incidental or consequential damage of any kind, including all damages arising out of any interruptions in operation of the product and all damages to software.

No person, firm, or representative is authorized to assume any obligation or to make any warranty on behalf of the Dukane Corporation other than as stated above.

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Models 8062/8802 Contents US Type UK Type Europe Type Projector With Lens Cap Projector FeaturesPower cord Soft carrying case Remote controlPower cord Only use the power cord that came with the projectorDevices you will be using to the projector Reference Part NamesCursor buttons Auto button Blank button Volume button Mute buttonFreeze button Keyboard buttons Position buttonAdjusting the Projectors Elevator Feet Setting UP the ProjectorTop view Side view Adjusting the Screen Size and Projection DistanceScreen Connecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerConnecting to a Display Monitor Operating the remote control Using the Remote ControlPutting batteries into the remote control unit Turning on the Power Selecting an Input Signal Turning OFF the Power Temporarily Muting the Sound Adjusting the VolumePress the Volume button Press Buttons to adjust VolumePress the Position button Adjusting the PositionUse Buttons to adjust Position Press the Auto button Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Automatic Adjustment for Video InputOn the screen to aid you in correcting the distortion Correcting Keystone DistortionsPress the Keystone button As illustrated on the right, a dialog will appearFreezing the Screen Using the Magnify FeatureTemporarily Blanking the Screen Signal SearchingSelecting the Aspect Ratio Press Buttons to adjust the level Using the Menu FunctionsSelect a menu using Buttons Then press Or Enter button Select an item using Buttons, then press Or Enter buttonOperating the PC Screen Available Functions Remote Control OperationDo not use the projector with the lamp cover removed High Voltage High Temperature High PressureLamp Replacing the lamp Caring for the air filter AIR FilterReplacing the air filter Caring for the lens Caring for the cabinet and remote control transmitterOther Care Caring for the inside of the projectorFor Technical see the end of this manual Main Menu Multifunctional SettingsMain Menu PICTURE2 Menu Picture 1 MenuPicture 2 Menu PICTURE1 MenuVideo Input MenuInput Menu AutoStart UP Screen MenuScreen Menu BlankAuto OFF VolumeOption Menu Option MenuRelated Messages Power Lamp Temp Regarding the Indicator LampsVol.2-6 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-3Unit mm SpecificationsDimension Diagram SpecificationWarranty and AFTER-SERVICE Sub 15-pin Shrink Signal Connector PIN AssignmentSignal Terminal Specification RGB in 1/2Resolution FH kHz FV Hz Rating Signal mode Display mode Example of Computer SignalInitial SET Signals USB Mouse Connection to the Mouse ControlADB Mouse Serial MouseProtocol Command dataConsist of header 7 bytes + command data 6 bytes RS-232C CommunicationIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset Command日本語 Command data chartBe EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices Page Page Page Page Page Page Dukane Corporation Audio Visual Products 401-8062/8802

8062, 8802 specifications

The Dukane 8802 and 8062 ultrasonic welding systems represent a significant advancement in the field of ultrasonic technology, designed for precision joining of thermoplastics and metals. These systems combine innovative engineering with user-friendly features, making them an ideal choice for various industrial applications.

One of the defining features of the Dukane 8802 and 8062 is their robust ultrasonic generator that provides consistent power output. This ensures that every weld is reliable and repeatable, crucial for high-volume production environments. The systems utilize a patented Smart Generator technology, capable of automatically tuning to the optimal frequency, thus maximizing efficiency and enhancing acoustic performance.

Both models are equipped with a high-performance ultrasonic transducer, which converts electrical energy into mechanical energy. This transducer is designed for durability and long-term performance, ensuring minimal downtime and reduced maintenance needs. The systems also feature advanced piezoelectric materials that enhance energy conversion, leading to superior welding results.

User convenience is paramount, reflected in the digital touchscreen interface that allows operators to easily set parameters, monitor real-time performance, and adjust settings as necessary. Multiple welding modes are available, including time, energy, and distance control, allowing users to select the best approach according to their specific application needs.

The Dukane 8802 and 8062 also incorporate a lightweight and ergonomic design, facilitating easy integration into existing production lines. The adjustable horn and fixture options offer versatility in handling different component shapes and sizes, making these systems suitable for a wide range of industries including automotive, medical, and consumer goods.

Moreover, both systems emphasize safety and compliance, featuring built-in sensors that prevent overload conditions and ensure weld quality. This focus on safety enhances operator confidence and protects expensive tooling.

In conclusion, the Dukane 8802 and 8062 ultrasonic welding systems stand out due to their advanced technology, efficiency, and operator-friendly design. These characteristics not only improve manufacturing processes but also contribute to cost savings and higher quality standards across various applications.
Top Page Image Contents