Dukane 8802, 8062 manual Using the Remote Control, Putting batteries into the remote control unit

Page 14

USING THE REMOTE CONTROL

Putting batteries into the remote control unit

CAUTION Precautions to observe in regards to the batteries

Always handle the batteries with care and use them only as directed. Improper use may result in battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Keep the battery away from children and pets.

Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.

When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).

When you dispose the battery, you should obey the law in the relative area or country.

1

Remove the battery

 

2

Insert the batteries

cover

 

Align and insert the two AA

 

Slide back and remove

 

 

batteries (that came with the

 

the battery cover in the

 

 

projector) according to their plus

 

direction of the arrow.

 

 

and minus terminals (as indicated

 

 

 

 

in the remote control).

 

 

 

 

 

3 Closecover the battery

Replace the battery cover in the direction of the arrow and snap it back into place.

Operating the remote control

The remote control works with both the projector's front and rear remote sensors.

The range of the remote sensor on the front and back is 3 meters with a 60-degree range (30 degrees to the left and right of the remote sensor).

Since the remote control uses infrared light to send signals to the projector (Class 1 LED), be sure to use the remote control in an area free from obstacles that could block the remote control's output signal to the projector.

 

degre

es

30

 

 

 

approximately 3 meters

s

 

degrees

e

 

re

 

 

g

 

 

e

 

 

d

30

 

3

 

0

 

 

approximately 3 meters

s e re g e d 0 3

ATTENTION Precautions to observe when using the remote control

Do not drop or otherwise expose the remote control to physical impact.

Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.

Remove the batteries from the remote control and store them in a safe place if you won't be using the remote control for an extended period.

Replace the batteries whenever the remote control starts to malfunction.

When strong light, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function. Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.

13

Image 14
Contents Models 8062/8802 Contents Soft carrying case Remote control Projector FeaturesPower cord US Type UK Type Europe Type Projector With Lens CapPower cord Only use the power cord that came with the projectorDevices you will be using to the projector Part Names ReferencePosition button Auto button Blank button Volume button Mute buttonFreeze button Keyboard buttons Cursor buttonsSetting UP the Projector Adjusting the Projectors Elevator FeetTop view Side view Adjusting the Screen Size and Projection DistanceScreen Connecting Your Devices Ports and Cables Function Projector Port Connection CablesConnecting Your Devices Connecting to a ComputerConnecting to a DVD Player Connecting to a VCRConnecting to a Display Monitor Operating the remote control Using the Remote ControlPutting batteries into the remote control unit Turning on the Power Selecting an Input Signal Turning OFF the Power Press Buttons to adjust Volume Adjusting the VolumePress the Volume button Temporarily Muting the SoundPress the Position button Adjusting the PositionUse Buttons to adjust Position Automatic Adjustment for Video Input Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Press the Auto buttonAs illustrated on the right, a dialog will appear Correcting Keystone DistortionsPress the Keystone button On the screen to aid you in correcting the distortionUsing the Magnify Feature Freezing the ScreenTemporarily Blanking the Screen Signal SearchingSelecting the Aspect Ratio Select an item using Buttons, then press Or Enter button Using the Menu FunctionsSelect a menu using Buttons Then press Or Enter button Press Buttons to adjust the levelAvailable Functions Remote Control Operation Operating the PC ScreenDo not use the projector with the lamp cover removed High Voltage High Temperature High PressureLamp Replacing the lamp AIR Filter Caring for the air filterReplacing the air filter Caring for the inside of the projector Caring for the cabinet and remote control transmitterOther Care Caring for the lensFor Technical see the end of this manual Main Menu Multifunctional SettingsMain Menu PICTURE1 Menu Picture 1 MenuPicture 2 Menu PICTURE2 MenuAuto Input MenuInput Menu VideoBlank Screen MenuScreen Menu Start UPOption Menu VolumeOption Menu Auto OFFRelated Messages Regarding the Indicator Lamps Power Lamp TempVol.2-3 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-6Specification SpecificationsDimension Diagram Unit mmWarranty and AFTER-SERVICE RGB in 1/2 Signal Connector PIN AssignmentSignal Terminal Specification Sub 15-pin ShrinkExample of Computer Signal Resolution FH kHz FV Hz Rating Signal mode Display modeInitial SET Signals Serial Mouse Connection to the Mouse ControlADB Mouse USB MouseRS-232C Communication Command dataConsist of header 7 bytes + command data 6 bytes ProtocolUsing the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCommand data chart 日本語Be EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices Page Page Page Page Page Page Dukane Corporation 401-8062/8802 Audio Visual Products

8062, 8802 specifications

The Dukane 8802 and 8062 ultrasonic welding systems represent a significant advancement in the field of ultrasonic technology, designed for precision joining of thermoplastics and metals. These systems combine innovative engineering with user-friendly features, making them an ideal choice for various industrial applications.

One of the defining features of the Dukane 8802 and 8062 is their robust ultrasonic generator that provides consistent power output. This ensures that every weld is reliable and repeatable, crucial for high-volume production environments. The systems utilize a patented Smart Generator technology, capable of automatically tuning to the optimal frequency, thus maximizing efficiency and enhancing acoustic performance.

Both models are equipped with a high-performance ultrasonic transducer, which converts electrical energy into mechanical energy. This transducer is designed for durability and long-term performance, ensuring minimal downtime and reduced maintenance needs. The systems also feature advanced piezoelectric materials that enhance energy conversion, leading to superior welding results.

User convenience is paramount, reflected in the digital touchscreen interface that allows operators to easily set parameters, monitor real-time performance, and adjust settings as necessary. Multiple welding modes are available, including time, energy, and distance control, allowing users to select the best approach according to their specific application needs.

The Dukane 8802 and 8062 also incorporate a lightweight and ergonomic design, facilitating easy integration into existing production lines. The adjustable horn and fixture options offer versatility in handling different component shapes and sizes, making these systems suitable for a wide range of industries including automotive, medical, and consumer goods.

Moreover, both systems emphasize safety and compliance, featuring built-in sensors that prevent overload conditions and ensure weld quality. This focus on safety enhances operator confidence and protects expensive tooling.

In conclusion, the Dukane 8802 and 8062 ultrasonic welding systems stand out due to their advanced technology, efficiency, and operator-friendly design. These characteristics not only improve manufacturing processes but also contribute to cost savings and higher quality standards across various applications.