Compaq DA-11411 warranty Standard Features Server Blade

Page 3

QuickSpecs

ProLiant BL20p and p-Class system

Standard Features (Server Blade)

ProLiant BL20p Server Blade

Processor

Intel Pentium III FC-PGA processor 1.40GHz

 

 

 

 

Upgradability

Upgradable to dual processing

 

 

 

 

 

 

Cache Memory

512-KB Level 2 Cache

 

 

 

 

 

Chipset

ServerWorks HE- SuperLite Chipset

 

 

Note: For more information regarding ServerWorks, please see the following URL:

 

 

http://www.serverworks.com/products/overview.html.

 

 

 

 

 

Memory

Standard

512MB PC133-MHz Registered ECC SDRAM DIMM Memory (2 X 256 MB)

 

 

 

(1 processor model)

 

 

Maximum

4096 MB

 

 

Standard

1024MB PC133-MHz Registered ECC SDRAM DIMM Memory (2 x 512 MB)

 

 

 

(2 processor model – not available in NA)

 

 

Maximum

4096 MB

 

 

Note: Memory must be installed in pairs.

 

 

 

 

 

Network Controller

Four NICs total:

 

 

 

Three Compaq NC3163 Fast Ethernet NIC PCI 10/100 with full WOL (Wake On LAN), one with PXE support

 

 

One 10/100 iLO NIC dedicated to management

 

 

Two NICs are upgradable to 10/100/1000T using the Dual Gigabit Ethernet NC7780 NIC option kit

 

 

 

 

Manageability

Integrated Lights-Out (iLO) Management Advanced (ASIC on the System Board)

 

 

 

 

 

Internal Storage

Hard Drives

None ship standard

 

 

Maximum Internal Storage

145.6 GB (internal drive cage) (2 x 72.8 GB Wide Ultra3, 1drives)

 

 

 

 

Expansion Slots

No PCI slots all features are integrated

ProLiant BL p-Class Server Blade Enclosure and Interconnects

ProLiant BL p - Class Server Blade Enclosure

6U (10.5-inch), 19-inch wide

Holds up to 8 ProLiant BL20p servers blades 10 bays per server blade enclosure

8 bays for server blades

2 outside bays for interconnect modules (RJ-45 patch panels or GbE interconnect switches) Server blades blind mate into the server blade enclosure backplane for power and data connections Up to 6 BL p-Class 6U server blade enclosures fit in a 42U rack

Server blade management module attached to the back of each BL p-Class 6U server blade enclosure to report events all servers and provide asset and inventory information

ProLiant BL p - Class Power Requirements

Redundant 200V 240V AC, 30 amp single-phase for NA and International Redundant 208V 30amp 3-phase 4 wire, NA

Redundant 380 415V 20A 3-phase 5 wire, Intl Redundant -48VDC ± 10%

DA-11411

World Wide — Version 4 — September 19, 2002

3

Image 3 Contents
Overview QuickSpecsConfiguration Steps Standard Features Server Blade ProLiant BL p Class Interconnect Switch Option ProLiant BL p Class RJ 45 patch panelRequired Network Cabling Power Bus Box Required Power Source Compaq ProLiant BL p Class Power System and RackInformation ProLiant BL p Class Power BL p Class Power DistributionProLiant Essentials Foundation Pack Software Standard FeaturesOS Support Intelligent ManageabilityAvailability Security Minimum Rack RequirementsRack Airflow Requirements Service and Support Models Options ProLiant Essentials Value Pack Software Storage ControllersCommunications BL p-Class Server Blade BL p-Class Power optionsPower Distribution Diagnostic OptionsCompaq Rack 9000 Series Opal Compaq Rack 10000 SeriesRack Options for Compaq Rack 7000 Series and Telco racks Rack Options for Compaq RackSeries Rack Options for Compaq Rack 9000 SeriesService and Support Offerings Rack Options for Compaq Rack 10000, 9000 and 7000 SeriesRack Options for Telco Racks Installation & Start-up Services Memory Slot MemoryTechnical Specifications Power requirements Operating and Performance DimensionsSpecifications for RJ-45 Patch Panel ConnectorPerformance WeightForwarding mode SafetyInput requirements WeightsSpecifications Ambient temperatureQuickSpecs Rated operating voltage Enclosures DimensionsMax total power supported Max current per power feedCurrent Specifications for Facility DCMax Rated Power Operating and Performance VoltageCompaq Rack Dimensions Total Cabinet Shipping Color QuickSpecs