Compaq 910, 1210, P710 manual Problem Items to Check Location

Page 21

Before calling your 1-800-OK-COMPAQ for service, please

5check that the items below are properly connected or set.

TROUBLESHOOTING In case of using a non-standard signal, please check the pin assignments and the signal timing of your computer with the specification outlined in Section 6. SPECIFICA- TIONS and Section 7. APPENDIX.

 

 

 

PROBLEM

 

ITEMS TO CHECK

 

LOCATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LED On

Contrast and brightness controls.

Front

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Green)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LED Off

Power switch.

Front

 

 

 

 

 

 

 

 

AC power cord disconnected.

Rear

No

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

picture

 

 

 

 

 

 

 

Signal cable disconnected.

Rear

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LED On

Computer power switch.

Computer

 

 

 

 

 

 

 

 

Power management function is active.

• Press any key on the keyboard

 

 

 

 

 

 

 

 

(Amber)

 

 

 

 

 

 

 

 

 

 

 

or move the mouse.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The following message appeared.

Signal cable disconnected.

Rear

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Computer power switch.

Computer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power management function is active.

• Press any key on the keyboard

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or move the mouse.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The following message appeared.

Input signal frequency range is too high or too low for the

• Check the specification of

 

 

ATTENTION

 

 

 

monitor to synchronize with.

 

graphics adapter

 

 

 

SIGNAL FREQUENCY

 

 

 

 

 

 

 

 

 

IS OUT OF RANGE.

 

 

 

 

 

 

 

 

 

FH @ @24.8KHz

FV @ 43.0

 

 

 

 

 

 

 

 

PLEASE CHANGE

 

 

 

 

 

 

 

 

 

SIGNAL TIMING.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Do "GEOMETRY-RESET" or "ALL RESET" for a standard signal.

Front (OSD)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjust HORIZ-SIZE, VERT-SIZE, HORIZ-PHASE, and

Front (OSD)

 

 

 

Display is

miss-

 

VERT-POSITION with non-standard signals.

 

 

picture

 

ing, center shifts,

Monitor may not be able to get full-screen image depend

 

 

 

or too small or too

 

on signal. In this case, please select other resolution, or

 

 

 

 

 

large of a display

 

other vertical refresh timing.

 

 

Abnormal

 

size

 

 

Make sure you wait a few seconds after adjusting the size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

of the image before changing or disconnecting the signal.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Display is dark or

"VIDEO LEVEL" is not at the appropriate position for

Front (OSD)

 

 

 

 

your graphics adapter output. (0.7v or 1.0Vp-p).

 

 

 

 

 

too bright

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH

- 1 -

Image 21
Contents User’s Guide Contents Introduction FeaturesDDC ModelLocation Considerations Cleaning Your MonitorScreen Position Adjustment Quick Operation ChartModel 19 Models UnpackingAcpower Connector Signal Input Connector DB9-15P Part NameControl Names 17 & 19 Models Control Names 22 Model Input Connector SELECT/OSD OFF ButtonSignal Cable Connection AC Power ConnectionConnecting to VGA Compatible System Connecting to two computers 22 ModelUSB System Basic Application RearUSB Installation of USB Function Functions How to adjust the screenItems Function Adjustment Items ModelHORIZ-PHASE Color ResetGeometry Reset ContrastMoire Cancel Fine Picture ModeMoire Cancel Level POWER-SAVE= Available Items Function POWER-SAVEScreen IconPincushion Geom VERT-STATIC HORIZ-STATIC Video Corner Puritybl Control LockHORIZ-PHASE Color TemperatureGeometry Reset Moire Cancel LevelGroup Problem Items to Check Location Items to Check Location ProblemSpecifications EN60950 TÜV-GS, NEMKO, SEMKO, DEMKO, Fimko Horizontal 30 96kHz SC-B104 Signal Cable Monitor Signal Input Connector DB9-15PAppendix Mounted on the Rear Panel PIN AssignmentsRegulatory Compliance Canadian Notice 216028-001