Christie Digital Systems 38-VIV302-01 user manual Troubleshooting

Page 47

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check matters below once again.

1.Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 12 ~ 15.

2.Check cable connection. Verify that all computer, video and power cord are properly connected.

3.Verify that all power is switched on.

4.If a projector still does not produce an image, re-start your computer.

5.If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn a computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and computer.)

6.If problem still exists, check following chart.

Problem:

Try these Solutions

No power.

Plug a projector into your AC outlet.

 

Turn MAIN ON/OFF switch to ON.

 

Press POWER ON/OFF switch to ON.

 

Make sure READY Indicator lights.

 

Wait 90 seconds after a projector is turned OFF when turning a projector back on.

 

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as

 

follows:

 

1. LAMP indicator lights bright and READY indicator turns off.

 

2. After 90 seconds, READY indicator lights green again and a projector may be

 

turned on by pressing Power ON-OFF button.

 

Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY

 

indicator flashes, a projector can not be turned on.

 

(See "TURNING ON/OFF PROJECTOR" section on page 21.)

 

Check Projection Lamp. (Refer to page 45.)

Image is out of

Adjust focus of a projector.

focus.

Check Projection Lens to see if it needs cleaning.

NOTE : Moving a projector from a cool temperature location to a warm temperature location

 

 

may result in moisture condensation on Projection Lens. In such an event, leave a

 

projector OFF and wait until condensation disappears.

Picture is Left/Right

Check Ceiling / Rear feature. (See “SETTING” section on page 39.)

reversed.

 

 

 

Picture is

Check Ceiling feature. (See “SETTING” section on page 39.)

Top/Bottom

 

reversed.

 

 

 

Some displays are

Check Display feature.(See “SETTING” section on page 39.)

not seen during

 

Operation.

 

 

 

No image.

Check connection between your computer or video equipment and a projector.

 

When turning a projector on, it takes about 30 seconds to display an image.

 

Check system that you select is corresponding with your computer or video equipment.

 

Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).

 

 

No sound.

Check audio cable connection from audio input source.

 

Adjust audio source.

 

Press VOLUME (+) button.

 

Press MUTE button.

 

 

47

Image 47
Contents Model To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationFor U.S.A. and Canada For Continental Europe SETTING-UP ProjectorConnecting AC Power Cord Positioning Projector Preparation Lens InstallationLens Shift Adjustment Moving Projector Preparation Picture Level and Tilt AdjustmentTerminals of Projector Connecting ProjectorReplacement of Terminal Input 1, 2 Connecting Projector INPUT/OUTPUT Terminals and Jacks InputAudio Output Jacks Terminals Projector Connecting to Computer2INPUT Terminals of a Projector Connecting to Video EquipmentBefore Operation TOP Controls and IndicatorsLaser Pointer Function Operation of Remote ControlRemote Control Batteries Installation Flow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Screen Menu Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorKeystone Adjustment Adjusting ScreenFocus Adjustment No Show Function Timer FunctionBasic Operation Picture Freeze Function Sound Menu Sound AdjustmentDirect Operation Menu OperationInput Computer InputSelecting Input Source Selecting Computer SystemPC System Menu Computer Input Automatic MULTI-SCAN SystemSelect Computer System Manually AutoResolution Computer Input Compatible Computer SpecificationsComputer Input PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Full screen Display areaDisplay area H Image Select Menu Picture Image AdjustmentImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input When Select Input 3 AV TerminalAV System Menu Video or S-VIDEO Selecting Video SystemVideo Input AutoCinema Progressive scan Video Input Image Level AdjustmentColor TintProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Projector To change code of Remote Control UnitLamp counter reset Wireless Mouse modeProjector mode Operating Wireless Mouse Operating Wireless MouseMaintenance InstallationCleaning Projection Lens Appendix AIR Filter Care and CleaningYellow Lamp Dim Lamp Red Lamp Mark on Lamp Appendix Lamp ManagementFigure shows case of replacing Lamp Appendix Lamp ReplacementLamp Handling Precautions Troubleshooting Service Technical Specifications HDB 15-PIN Terminal Analog Appendix Configurations of TerminalsUSB Port Terminal Part No -A 610 305 5152 1AA6P1P3895-- MY8K

38-VIV302-01 specifications

Christie Digital Systems has established itself as a leader in the visual display industry, and the Christie 38-VIV302-01 is a testament to this reputation. This model is designed to meet the demands of various professional applications, including control rooms, corporate environments, educational institutions, and entertainment venues.

One of the standout features of the 38-VIV302-01 is its advanced visualization technology. It incorporates robust 4K resolution capabilities, which provide crystal-clear images and vibrant colors. This is essential for applications that require detail and precision, as it enables users to see the most intricate of details in their visual content. With a wide color gamut, the projector can reproduce a vast array of colors, enhancing the overall viewing experience.

In terms of connectivity, the 38-VIV302-01 offers multiple input options, ensuring compatibility with a variety of sources. This flexibility allows users to connect different devices seamlessly without worrying about compatibility issues. The inclusion of HDMI, DisplayPort, and various analog inputs makes it easy to integrate into existing systems or to scale up as needs evolve.

Another key characteristic of the Christie 38-VIV302-01 is its state-of-the-art light source technology. It utilizes laser illumination, which not only improves brightness levels and contrast ratios but also extends the lifespan of the projector. This feature is particularly important for long-term installations, reducing maintenance costs and downtime for users.

The design of the projector is also noteworthy. It features a compact and lightweight build, making it easy to mount in various environments, from boardrooms to event spaces. The whisper-quiet operation ensures that it won't distract viewers during presentations or performances, making it particularly useful in settings where concentration and focus are paramount.

In addition to its hardware features, the Christie 38-VIV302-01 integrates advanced software capabilities. This includes support for collaborative platforms, allowing multiple users to contribute and engage with the content being displayed. Furthermore, it offers enhanced security features, ensuring that sensitive information remains protected.

Overall, the Christie 38-VIV302-01 embodies the company's commitment to quality and innovation in visual display technology, making it an ideal choice for professionals seeking reliable and high-performance projection solutions. With its impressive specifications and user-friendly features, it continues to set a standard within the industry.