Christie Digital Systems CX60, CX50, CX67 user manual FAN LED will no longer be illuminated

Page 17

Section 3: Operation

NOTES: 1) Avoid turning the projector on and off without waiting at least 52 seconds in between. In general, hot re-strikes reduce lamp life. 2) It is recommended that you do not unplug the projector until the cooling fan is off

– the FAN LED will no longer be illuminated.

STANDBY

Press STANDBY to blank the display while keeping the projector in a warmed-up and ready state. Note that the lamp and electronics remain ON in standby mode, even though the image turns to black and most functions are disabled. To leave standby press Exit or Menu . NOTE: The POWER LED is illuminated red.

MENU

Press Menu to display the Main menu. A list of several options appears for access to specific functions, such as Configuration or Image Settings. Press Menu again or Exit to exit all menus and return to presentation level.

ENTER

Press Enter to select a highlighted item or to accept a parameter adjustment and return to the previous menu or image.

EXIT

Press Exit to return to the previous level, such as the previous menu.

ARROW KEYS ON , OFF , ,

The arrow keys have a variety of functions depending on the situation. The most common uses are described below.

Use the ON or OFF to move through the options in a menu or submenu.

Use or to change a slidebar value—hold as desired for continuous adjustment

CONTRAST

Press Contrast to change the amount of white in your images. Use and until you reach the desired level of contrast—for best results, start low

and increase so that whites remain bright but are not distorted or tinted, and that light areas do not become white (i.e., are “crushed”). Conversely, low contrast causes dim images. See Image Settings.

BRIGHTNESS

 

Press Brightness

to increase or decrease the amount of black in the image. Use

and

until you reach the desired level of contrast—for best results,

start high and decrease so that dark areas do not become black (i.e., are “crushed”). Conversely, high brightness changes black to dark gray, causing washed-out images. See Image Settings.

3-4 RPMX/CX50/CX60/CX67 User’s Manual

Image 17
Contents Table of Contents Introduction Key FeaturesFor detailed product specifications, see Section Components Vertical configurationHow the projector works For Rpmx For CX50/CX60/CX67Purchase Record Purchase Record and ServicingPage Connections Source SetupSource Analog VGA Connector Source Setup Video Loop Through Composite Video Loop ThroughSerial Port Connections If using a computer Single Projector10. Multiple Projector RS-232 Connection Requirements Power ConnectionPage Projection Head Module OperationProjector Overview Normal LED Status Keypad Commands Using the KeypadFAN LED will no longer be illuminated Refer to 3.7 Using Multiple Projectors for more details Accessing the Main Menu Adjusting SlidebarsTo save or Exit to Adjusting an ImagePresentation OptionsSize and Position Menu Resize PresetsNo Resizing Tiled Resize PresetsPixel Tracking SizeVert Stretch Position Pixel phaseBrightness Color SetupContrast 12. Gamma options Video Options 13. Creating a Custom Color Temperature15. Input Video Black Input Levels for experienced users onlyBlack Levels & Input Drives Input Select Mode Memory StatusWhite Boost Language Image OrientationCommunication Menu Preference25. Assigning Projector ID Tiling SetupColor and Uniformity 27. Expanded Options in Resize PresetsDiagnostics & Service Lamp Menu Choosing a Lamp PowerOptimizes Sets to Default System Status Auto SetupProjectors Using MultiplePreliminary Setup When matching screens in a display wall, do the followingDefining the Size Display WallAdjust Color Temperature Enable Primary Color AdjustmentPrimary Color Adjustment Status LED Codes Error CodesError, Lamp shut off DMD errorLamp strike failure Lamp failure, BallastPage Maintenance Attachments Power cordCleaning and Maintenance Lamp ReplacementReplacing Keypad BatteriesRemove the lamp Access the lamp moduleSee also, 3.4 The Lamp Menu in Section Install a new lampClose lamp door and record new lamp serial number For Rpmx 38-GFX101-01, CX67 38-GFX005-01 Figure Projection Lens FocusSymptom TroubleshootingProjector does not power on when the Power key is pressed Projector is on, but no image is displayedSymptom The display has suddenly frozen… Symptom The display is jittery or unstable…Display is faint… Display is reversed and/or upside down…Display is noisy… Display is not sharp or clean…Colors in the display are inaccurate… Specifications Picture Offset Adjustment Range Range of Motion Control Signal Infrared IR Control InputDVI Input RS-232Viewing Angle Power RequirementsLamps LensSize includes lens, adjuster and mounting rails Weight including adjusterFor RPMX-100U 38-GFX101-01 For RPMX-100UFor RPMX-100U 38-GFX003-xx For CX50-100UFor CX60-100U 38-GFX004-xxRegulatory Compliance ANSI/UL 60950 3rd Edition For CX67-100U38-GFX006-xx Specifications Glossary Display Setting Color TemperatureCheckbox Color ShiftHelp Screen Input SignalHorizontal Frequency Horizontal OffsetResolution lens Pixel PhaseResolution projector Ntsc VideoSwitcher Source SetupRGB Video RS-422Vertical Frequency Variable ScanVertical Offset Video DecoderAcceptable Signal Types Acceptable RGB Input Signal Timing RPMX/CX50/CX60/CX67 User’s Manual B-3 Page Keypad Reference Page Serial Communication Cables Page Menu Tree Page About IndexInput Levels Power Level Switching Pixel Phase