Christie Digital Systems 38-VIV207-01 user manual Troubleshooting

Page 42

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check the matters below once again.

1.Make sure you have connected a projector to your computer or video equipment as described in the section "CONNECTING PROJECTOR" on pages 11 ~ 13.

2.Check cable connection. Verify that all computer, video and power cord are properly connected.

3.Verify that all power is switched on.

4.If a projector still does not produce an image, re-start your computer.

5.If an image still does not appear, unplug a projector from your computer and check your computer monitor's display. The problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn the computer and monitor off before you power up the projector. Power the equipment back on in order of : Projector and computer.)

6.If the problem still exists, check the following chart.

Problem:

Try these Solutions

No power.

Plug a projector into your AC outlet.

 

Make sure READY Indicator lights.

 

Wait 90 seconds after a projector is turned OFF when turning the projector back on.

 

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as

 

follows:

 

1. LAMP indicator lights bright and READY indicator turns off.

 

2. After 90 seconds, READY indicator lights green again and a projector may be

 

turned on by pressing Power ON-OFF button.

 

Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY

 

indicator flashes, the projector can not be turned on.

 

(See "TURNING ON/OFF PROJECTOR" section on page 19.)

 

Check Projection Lamp. (Refer to page 38.)

 

 

Image is out of

Adjust focus of a projector.

focus.

Make sure a projection screen is at least 4.1’ (1.2m) from the projector.

Check Projection Lens to see if it needs cleaning.

 

 

NOTE : Moving a projector from a cool temperature location to a warm temperature location

 

may result in moisture condensation on Projection Lens. In such an event, leave a

 

projector OFF and wait until condensation disappears.

 

 

Picture is Left/Right

Check Ceiling / Rear feature. (See “SETTING” section on page 36.)

reversed.

 

 

 

Picture is

Check Ceiling feature. (See “SETTING” section on page 36.)

Top/Bottom

 

reversed.

 

 

 

Some displays are

Check Display feature.(See “SETTING” section on page 36.)

not seen during the

 

Operation.

 

 

 

No image.

Check the connection between your computer or video equipment and a projector.

 

When turning a projector on, it takes about 30 seconds to display an image.

 

Check the system that you select is corresponding with your computer or video

 

equipment.

 

Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).

No sound.

Check audio cable connection from audio input source.

 

Adjust the audio source.

 

Press VOLUME (+) button.

 

Press MUTE button.

 

 

42

Image 42
Contents Model To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact DesignPreparation Name of Each Part of ProjectorHOT AIR Exhausted SETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Preparation Positioning Projector Room LightPreparation Adjustable Feet Moving ProjectorTerminals of Projector Connecting ProjectorUSB Connector Series B Monitor OutputTerminals Connecting to ComputerConnecting Projector ProjectorConnecting to Video Equipment Audio VideoBefore Operation Operation of Remote ControlInside the Battery Compartment BOX Laser Pointer FunctionZoom Button Point Volume + ButtonsTimer Button Select ButtonTOP Controls and Indicators Lamp Replace IndicatorHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Guide WindowSound Menu Turning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus Adjustment Adjusting ScreenZoom Adjustment Keystone AdjustmentSound Adjustment Computer Input Selecting Input SourceRGB Selecting Computer System AutoPC System Menu Computer Input Compatible Computer Specifications ResolutionXGA PC Adjust Menu PC AdjustmentAuto PC Adjustment Auto PC AdjComputer Input Manual PC Adjustment Display area Display area HFull screen Image Level Select Menu Picture Image AdjustmentsImage Level Select Direct Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Input VideoVideo PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N Component Video Signal FormatSelecting Video System AV System Menu Video or S-VIDEOCinema Video Input Image Level Adjustment Provides image at a normal video aspect ratio of 4 Setting Setting MenuSetting Menu To change the code of the Remote Control Unit To change the code of ProjectorLamp Replacement AppendixLamp Replace Lamp Handling Precautions Appendix Lamp Replace CounterOperating Wireless Mouse InstallationOperating Wireless Mouse Cleaning Projection Lens MaintenanceAIR Filter Care and Cleaning RecommendationTroubleshooting Service Technical Specifications USB Connector Series B Appendix Configurations of TerminalsControl Port Connector Computer INPUT-1 and Monitor OUT Terminals AnalogPOA-MCMAC Appendix Optional PartsPOA-MCPS2 POA-MACAPPage Part No -A 610 307 0469 1AA6P1P4023-- MC3K

38-VIV207-01 specifications

Christie Digital Systems, a leader in digital projection technology, offers a remarkable solution for professional installations with the 38-VIV207-01 model. This innovative display is designed to cater to a wide range of applications, from corporate environments to entertainment venues, enhancing visual experiences with advanced features and technologies.

One of the standout characteristics of the Christie 38-VIV207-01 is its impressive resolution. Sporting a high-definition display, it ensures that users enjoy crisp, vibrant visuals that are essential for any professional setting. The clarity and accuracy of the images make it ideal for presentations, video conferencing, and immersive media experiences, allowing for detailed content to be appreciated as intended.

In terms of brightness, the 38-VIV207-01 delivers outstanding performance. With a significant brightness level, it ensures visibility in various lighting conditions, making it a versatile choice for both dimly lit and well-lit environments. This feature is particularly beneficial for settings such as trade shows or large auditoriums, where ambient light can often detract from the viewing experience.

The model is also equipped with a range of connectivity options, allowing it to integrate seamlessly with different systems and devices. Whether connecting to a laptop, media player, or other sources, the 38-VIV207-01 offers flexibility that caters to diverse user needs. This versatility is further enhanced by compatibility with various input formats, ensuring that it meets the demands of modern technology.

For users looking for reliability, Christie has built the 38-VIV207-01 with durability in mind. Designed for long-term operation, it features enhanced cooling and energy-efficient components that minimize downtime. This makes it an ideal choice for installations that require consistent performance over extended periods.

Additionally, the model boasts advanced color calibration capabilities, ensuring that the display maintains accurate color reproduction. This is essential for applications where color fidelity is critical, such as graphic design, video production, and medical imaging.

Overall, the Christie Digital Systems 38-VIV207-01 stands out as a top-tier display solution, combining high definition, brightness, connectivity, and reliability. Whether for corporate or entertainment use, its array of features and technical advancements make it a worthy investment for those seeking superior visual performance.