Christie Digital Systems 38-VIV306-01 user manual Compliances, Camden Drive Cypress, CA 90630 USA

Page 4

COMPLIANCES

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number	: 38-VIV303-01/38-VIV306-01
Trade Name	: Christie
Responsible party	: CHRISTIE DIGITAL SYSTEMS, Inc.
Address	: 10550 Camden Drive Cypress, CA 90630 USA
Telephone No.	: (714) 236-8610

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be

unable to insert the plug into the outlet, contact your electrician.	GROUND

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

4

Image 4

Contents Draft To the Owner Safety Instructions Voor de klanten in NederlandCompliances Camden Drive Cypress, CA 90630 USATable of Contents Features and Design Compact Design Digital Zoom for ComputerName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Positioning Projector Preparation Lens InstallationRoom Light Preparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connecting Projector Terminals of ProjectorConnect computer output Digital DVI-D type to this terminal Refer to P13Terminals Connecting to ComputerA Projector Connecting to Video Equipment Operation of Remote Control Inside the Battery Compartment BOXBefore Operation Laser Pointer FunctionRemove battery Compartment lidSlide batteries into CompartmentTOP Controls and Indicators Operating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Press Menu Button while connecting to PC input source Used to adjust picture imageBefore Operation Menu BAR Used to selectBasic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Keystone AdjustmentFocus adjustment may not function properly if the image is Corrected by Keystone adjustmentSound Adjustment Computer Input Selecting Input SourceSelecting Computer System Rgbav HdcpAuto Automatic MULTI-SCAN SystemPC System Menu PC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area H Display areaFull screen Picture Image Select Image Level Select DirectImage Level Select Menu Image Select MenuPicture Screen Adjustment Screen MenuWhen video input signal is connected to Video jack Video InputVideo Select VideoSelecting Video System AutoAV System Menu Video or S-VIDEO AV System Menu Component VideoPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Image Adjust Menu Picture Image AdjustmentsPicture Image List Mode Color temp White balance RedWhite balance Green White balance BlueSetting Menu SettingSetting Menu Anamorphic Blue backDisplay Menu positionTo change the code of the Remote Control Unit Power managementRemote control To change the code of ProjectorWireless Mouse mode Projector modeLamp counter reset Factory defaultOperating Wireless Mouse InstallationOperating Wireless Mouse AppendixIndicatorIndicator MaintenanceStation Appendix AIR Filter Care and Cleaning Cleaning Projection LensRecommendation Pull up and removeLamp Replacement Lamp ReplaceMessage Lamp replace counter reset? is displayed. Move Reset Lamp Replace CounterAppendix Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Service Appendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree PC sourceSystem Setting Sound Technical Specifications Appendix Configurations of Terminals Control Port ConnectorUSB Connector Series B Computer INPUT-1 and Monitor OUT Terminals AnalogTo the sales and service engineer Lens ReplacementAppendix Optional Parts Appendix Part No -A 610 316 2553 1AA6P1P4203A- ME5KL