Christie Digital Systems 38-VIV306-01 Appendix AIR Filter Care and Cleaning, Recommendation

Page 43

APPENDIX

AIR FILTER CARE AND CLEANING

Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up and adversely affect life of a projector. Clean Air Filter following steps below:

1

Turn off a projector, and disconnect AC power cord from AC

outlet.

2

Turn a projector upside down and remove Air Filter (2 used) by

pulling latches upward.

3

Clean Air Filter with a brush or wash out dust and particles.

4

inserted.Replace Air Filter properly. Make sure that Air Filter is fully

CAUTION

Do not operate a projector with Air Filter removed. Dust may accumulate on LCD Panel and Projection Mirror degrading picture quality.

Do not put small parts into Air Intake Vents. It may result in malfunction of a projector.

AIR FILTER

Pull up and remove.

RECOMMENDATION

We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments may cause poor image quality.

When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements inside a projector. This condition may degrade quality of a projected image.

When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.

CLEANING PROJECTION LENS

Follow these steps to clean Projection Lens:

1

Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.

Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.

2

3

Lightly wipe a cleaning cloth over Projection Lens.

When a projector is not in use, replace Lens Cover.

43

Image 43
Contents Draft To the Owner Voor de klanten in Nederland Safety InstructionsCamden Drive Cypress, CA 90630 USA CompliancesTable of Contents Compact Design Digital Zoom for Computer Features and DesignName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Positioning Projector Preparation Lens InstallationRoom Light Installing Projector in Proper Position Preparation Adjustable FeetPreparation Moving Projector Refer to P13 Connecting ProjectorTerminals of Projector Connect computer output Digital DVI-D type to this terminalTerminals Connecting to ComputerA Projector Connecting to Video Equipment Laser Pointer Function Operation of Remote ControlInside the Battery Compartment BOX Before OperationCompartment Remove batteryCompartment lid Slide batteries intoTOP Controls and Indicators Operating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Used to select Press Menu Button while connecting to PC input sourceUsed to adjust picture image Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorCorrected by Keystone adjustment Adjusting ScreenKeystone Adjustment Focus adjustment may not function properly if the image isSound Adjustment Rgbav Hdcp Computer InputSelecting Input Source Selecting Computer SystemAuto Automatic MULTI-SCAN SystemPC System Menu Auto PC Adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Select Menu Picture Image SelectImage Level Select Direct Image Level Select MenuScreen Menu Picture Screen AdjustmentSelect Video When video input signal is connected to Video jackVideo Input VideoAV System Menu Component Video Selecting Video SystemAuto AV System Menu Video or S-VIDEOCinema Picture level adjusted for picture with fine toneProvides image at a wide screen ratio of 16 Provides image at a normal video aspect ratio of 4Image Adjust Menu Picture Image AdjustmentsPicture Image List Mode White balance Blue Color tempWhite balance Red White balance GreenSetting Menu SettingSetting Menu Menu position AnamorphicBlue back DisplayTo change the code of Projector To change the code of the Remote Control UnitPower management Remote controlFactory default Wireless Mouse modeProjector mode Lamp counter resetAppendix Operating Wireless MouseInstallation Operating Wireless MouseIndicatorIndicator MaintenanceStation Pull up and remove Appendix AIR Filter Care and CleaningCleaning Projection Lens RecommendationLamp Replace Lamp ReplacementPointer to Yes and then press Select button Message Lamp replace counter reset? is displayed. MoveReset Lamp Replace Counter Appendix Lamp Replace CounterTroubleshooting Service Appendix Indicators and Projector Condition Resolution Appendix Compatible Computer SpecificationsPC source Menu TreeSystem Setting Sound Technical Specifications Computer INPUT-1 and Monitor OUT Terminals Analog Appendix Configurations of TerminalsControl Port Connector USB Connector Series BTo the sales and service engineer Lens ReplacementAppendix Optional Parts Appendix Part No -A 610 316 2553 1AA6P1P4203A- ME5KL