Christie Digital Systems 38-VIV306-01 user manual Troubleshooting

Page 46

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check matters below once again.

1.Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 12 ~ 14.

2.Check cable connection. Verify that all computer, video and power cord are properly connected.

3.Verify that all power is switched on.

4.If a projector still does not produce an image, re-start your computer.

5.If an image still does not appear, unplug a projector from your computer and check your computer monitor's display. Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and computer.)

6.If problem still exists, check following chart.

Problem:

Try these Solutions

No power.

Plug a projector into your AC outlet.

 

Make sure READY Indicator lights.

 

Wait 90 seconds after a projector is turned OFF when turning a projector back on.

 

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as

 

follows:

 

1. LAMP indicator lights bright and READY indicator turns off.

 

2. After 90 seconds, READY indicator lights green again and a projector may be

 

turned on by pressing Power ON-OFF button.

 

Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY

 

indicator flashes, a projector cannot be turned on.

 

(See "TURNING ON/OFF PROJECTOR" section on page 20.)

 

Check Projection Lamp. (Refer to page 44.)

 

 

Image is out of

Adjust focus of a projector.

focus.

Make sure a projection screen is at least 4.6’ (1.4m) from a projector.

Check Projection Lens to see if it needs cleaning.

 

 

NOTE : Moving a projector from a cool temperature location to a warm temperature location

 

may result in moisture condensation on Projection Lens. In such an event, leave a

 

projector OFF and wait until condensation disappears.

 

 

Picture is Left/Right

Check Ceiling/Rear feature. (See “SETTING” section on page 38.)

reversed.

 

 

 

Picture is

Check Ceiling feature. (See “SETTING” section on page 38.)

Top/Bottom

 

reversed.

 

 

 

Some displays are

Check Display feature.(See “SETTING” section on page 38.)

not seen during

 

Operation.

 

 

 

No image.

Check connection between your computer or video equipment and a projector.

 

When turning a projector on, it takes about 30 seconds to display an image.

 

Check system that you select is corresponding with your computer or video equipment.

 

Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).

No sound.

Check audio cable connection from audio input source.

 

Adjust audio source.

 

Press VOLUME (+) button.

 

Press MUTE button.

 

 

46

Image 46
Contents Draft To the Owner Safety Instructions Voor de klanten in NederlandCompliances Camden Drive Cypress, CA 90630 USATable of Contents Features and Design Compact Design Digital Zoom for ComputerName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Positioning Projector Preparation Lens InstallationRoom Light Preparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connect computer output Digital DVI-D type to this terminal Connecting ProjectorTerminals of Projector Refer to P13Terminals Connecting to ComputerA Projector Connecting to Video Equipment Before Operation Operation of Remote ControlInside the Battery Compartment BOX Laser Pointer FunctionSlide batteries into Remove batteryCompartment lid CompartmentTOP Controls and Indicators Operating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Press Menu Button while connecting to PC input sourceUsed to adjust picture image Used to selectTurning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus adjustment may not function properly if the image is Adjusting ScreenKeystone Adjustment Corrected by Keystone adjustmentSound Adjustment Selecting Computer System Computer InputSelecting Input Source Rgbav HdcpAuto Automatic MULTI-SCAN SystemPC System Menu PC Adjust Menu PC AdjustmentAuto PC Adjustment Auto PC AdjComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image SelectImage Level Select Direct Image Select MenuPicture Screen Adjustment Screen MenuVideo When video input signal is connected to Video jackVideo Input Select VideoAV System Menu Video or S-VIDEO Selecting Video SystemAuto AV System Menu Component VideoPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Image Adjust Menu Picture Image AdjustmentsPicture Image List Mode White balance Green Color tempWhite balance Red White balance BlueSetting Menu SettingSetting Menu Display AnamorphicBlue back Menu positionRemote control To change the code of the Remote Control UnitPower management To change the code of ProjectorLamp counter reset Wireless Mouse modeProjector mode Factory defaultOperating Wireless Mouse Operating Wireless MouseInstallation AppendixIndicatorIndicator MaintenanceStation Recommendation Appendix AIR Filter Care and CleaningCleaning Projection Lens Pull up and removeLamp Replacement Lamp ReplaceAppendix Lamp Replace Counter Message Lamp replace counter reset? is displayed. MoveReset Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Service Appendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree PC sourceSystem Setting Sound Technical Specifications USB Connector Series B Appendix Configurations of TerminalsControl Port Connector Computer INPUT-1 and Monitor OUT Terminals AnalogTo the sales and service engineer Lens ReplacementAppendix Optional Parts Appendix Part No -A 610 316 2553 1AA6P1P4203A- ME5KL