BOXLIGHT CP322ia user manual Lamp, Replacing the lamp

Page 27

THE LAMP (continued)

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.2 7 ) and "Regarding the Indicator Lamps" (Vol.2 8 ) for details.)

1Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes, and prepare a new lamp (sold separately: DT00511 for S3170A/DT00521 for ED-X3270A)

2After making sure that the projector has cooled adequately, slowly flip over the projector, so that the bottom is facing up

5Insert the new lamp, and tighten the 1 screw firmly to lock it in place

•Also steadily push the opposite side of the screwed side of the

lamp into the unit.

3Unscrew the 2 screws, and remove the lamp cover

6Replace the lamp cover, and tighten the 2 screws firmly to lock it in place

4Unscrew the 1 screw, and slowly pull out the lamp by the handle

• Be careful not to touch the inside of the lamp case.

7Slowly turn the projector so that the top is facing up

8Turn on the projector power, and using the menu, reset the lamp timer

•To reset the lamp timer, from the OPTION menu, select LAMP TIME.

ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

•Do not use with lamp cover removed.

•Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.

•When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power ON.

NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp.

26

Image 27

Contents CP322ia Contents Cable Projector FeaturesFor the remote Control Power cordConnect your devices to the projector Only use the power cord that came with the projectorDevices you will be using to the projector Power cordReference Part NamesFreeze button Keyboard buttons Auto button Blank button Volume button Mute buttonRGB button Search button STANDBY/ON button Video button 15 Aspect button Magnify buttonsAdjusting the Projectors Elevator Feet Setting UP the ProjectorScreen Adjusting the Screen Size and Projection DistanceConnecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerConnecting to a Display Monitor Using the Remote Control Putting batteries into the remote control unitOperating the remote control Remove the lens cap Turning on the PowerPrecautions Press the STANDBY/ON button control panel or remote controlSelecting an Input Signal If selecting video input Press the Video buttonPress the Input button Turning OFF the Power Temporarily Muting the Sound Adjusting the VolumePress the Volume button Press the , buttons to adjust the volumeAdjusting the Position Use the , , , buttons to adjust the positionPress the Position button Press the Auto button Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Automatic Adjustment for Video InputOn the screen to aid you in correcting the distortion Correcting Keystone DistortionsPress the Keystone button As illustrated on the right, a dialog will appearPress the , buttons to zoom in and out of the selected area Using the Magnify FeatureFreezing the Screen Press the Magnify on buttonSignal Searching Selecting the Aspect RatioTemporarily Blanking the Screen Using the Menu Functions Press the / buttons to adjust the level Press the Menu button Operating the PC Screen Available Functions Remote Control OperationHigh Voltage High Temperature High Pressure LampDo not use the projector with the lamp cover removed Replacing the lamp LampCaring for the air filter AIR FilterReplacing the air filter AIR FilterCaring for the lens Caring for the cabinet and remote control transmitterOther Care Caring for the inside of the projectorFor Technical see the end of this manual Multifunctional Settings Main MenuMain Menu PICTURE2 Menu Picture 1 MenuPicture 2 Menu PICTURE1 MenuVideo Input MenuInput Menu AutoStart UP Screen MenuScreen Menu BlankOption Menu Option MenuRelated Messages Power Lamp Temp Regarding the Indicator LampsVol.2-6 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-3Unit mm SpecificationsDimension Diagram SpecificationWarranty and AFTER-SERVICE Page Signal Connector PIN Assignment RGB in 1/2Sub 15-pin Shrink Resolution FH kHz FV Hz Rating Signal mode Display mode Example of Computer SignalInitial SET Signals USB Mouse Connection to the Mouse ControlADB Mouse Serial MouseProtocol Command dataConsist of header 7 bytes + command data 6 bytes RS-232C CommunicationIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset Command日本語 Command data chartBe EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices Limited Warranty Disclaimer of Unstated Warranties