BOXLIGHT CP322ia Phenomena That May Easily Be Mistaken for Machine Defects, Vol.2-2, Vol.2-3

Page 39

WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)

Phenomena That May Easily Be Mistaken for Machine Defects

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.

Phenomenon

Cases not involving a machine defect

Items to be confirmed

Reference

Page(s)

 

 

 

 

 

 

 

 

The main power source is not ON.

Turn on the main power.

Vol.1-3, 14

 

 

 

 

The electrical power cord is not plugged in.

Correctly connect the power cord.

 

 

 

 

 

 

Power does not

 

Be sure to press the “O” (power OFF) side

 

come ON

The main power source has been

of the main power switch, and leave this OFF

Vol.1-14

 

interrupted during operation, such as by

for approximately 20 minutes. After the unit

 

a power outage (blackout), etc.

has sufficiently cooled down, turn ON the

 

 

 

power source.

 

 

 

 

 

No sound or

The input changeover settings

Select the input signal, and

Vol.1-15

are mismatched.

correct the settings.

pictures are

 

 

 

 

 

 

 

outputted

No signal is being inputted.

Correctly connect the connection cord.

Vol.1-10, 11

 

 

 

 

 

The electrical wiring to this unit

Correctly connect the connection cord.

Vol.1-10, 11

 

is not correctly connected.

Pictures are

 

 

 

 

 

The volume setting has been set at (or

 

Vol.1-17

displayed, but no

Adjust the VOLUME setting to a higher level.

adjusted to) an extremely low level.

sounds are heard

 

 

 

 

 

The MUTE mode is the current setting.

Press the MUTE button to release

Vol.1-17

 

 

 

(change) the MUTE mode setting.

 

 

The electrical wiring to this unit

Correctly connect the connection cord.

Vol.1-10, 11

Sounds are

is not correctly connected.

 

 

heard, but no

The brightness setting has been set at

Adjust the BRIGHT setting to a

Vol.2-2

pictures are

(or adjusted to) an extremely low level.

brighter level.

 

displayed

 

 

 

The lens cap has not been removed.

Remove the lens cap.

Vol.1-14

 

 

 

 

 

Colors have a faded-

 

Perform picture adjustments by changing the

Vol.2-3

out appearance

Color depth setting or color tone setting

COLOR BAL R, the COLOR BAL B, and/or the

Color tone is poor

 

TINT settings, etc.

 

 

 

 

 

 

The brightness setting and/or contrast

Perform picture adjustments by changing the

Vol.2-2

 

setting has not been properly adjusted.

BRIGHT and/or CONTRAST settings, etc.

 

Pictures appear

The WHISPER mode is the current

Change (by releasing) from the

Vol.2-6

dark

setting.

WHISPER mode.

 

 

Lamp is approaching the end of its

Exchange the old lamp with a new

Vol.1-25, 26

 

product lifetime.

lamp.

 

 

 

 

 

Pictures appear

Either the FOCUS setting or the H

Adjust the FOCUS and H PHASE settings.

Vol.1-15

blurry

PHASE is not properly adjusted.

Vol.2-3

 

 

 

 

 

NOTE

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

ENGLISH

9

Page 38 Page 40
Image 39
Page 38 Page 40
Contents CP322ia Contents Cable Projector FeaturesFor the remote Control Power cordConnect your devices to the projector Only use the power cord that came with the projectorDevices you will be using to the projector Power cordReference Part NamesFreeze button Keyboard buttons Auto button Blank button Volume button Mute buttonRGB button Search button STANDBY/ON button Video button 15 Aspect button Magnify buttonsAdjusting the Projectors Elevator Feet Setting UP the ProjectorScreen Adjusting the Screen Size and Projection DistanceConnecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerConnecting to a Display Monitor Using the Remote Control Putting batteries into the remote control unitOperating the remote control Remove the lens cap Turning on the PowerPrecautions Press the STANDBY/ON button control panel or remote controlSelecting an Input Signal If selecting video input Press the Video buttonPress the Input button Turning OFF the Power Temporarily Muting the Sound Adjusting the VolumePress the Volume button Press the , buttons to adjust the volumeAdjusting the Position Use the , , , buttons to adjust the positionPress the Position button Press the Auto button Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Automatic Adjustment for Video InputOn the screen to aid you in correcting the distortion Correcting Keystone DistortionsPress the Keystone button As illustrated on the right, a dialog will appearPress the , buttons to zoom in and out of the selected area Using the Magnify FeatureFreezing the Screen Press the Magnify on buttonSignal Searching Selecting the Aspect RatioTemporarily Blanking the Screen Using the Menu Functions Press the / buttons to adjust the levelPress the Menu button Operating the PC Screen Available Functions Remote Control OperationHigh Voltage High Temperature High Pressure LampDo not use the projector with the lamp cover removed Replacing the lamp LampCaring for the air filter AIR FilterReplacing the air filter AIR FilterCaring for the lens Caring for the cabinet and remote control transmitterOther Care Caring for the inside of the projectorFor Technical see the end of this manual Multifunctional Settings Main MenuMain Menu PICTURE2 Menu Picture 1 MenuPicture 2 Menu PICTURE1 MenuVideo Input MenuInput Menu AutoStart UP Screen MenuScreen Menu BlankOption Menu Option MenuRelated Messages Power Lamp Temp Regarding the Indicator LampsVol.2-6 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-3Unit mm SpecificationsDimension Diagram SpecificationWarranty and AFTER-SERVICE Page Signal Connector PIN Assignment RGB in 1/2Sub 15-pin Shrink Resolution FH kHz FV Hz Rating Signal mode Display mode Example of Computer SignalInitial SET Signals USB Mouse Connection to the Mouse ControlADB Mouse Serial MouseProtocol Command dataConsist of header 7 bytes + command data 6 bytes RS-232C CommunicationIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset Command日本語 Command data chartBe EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices Limited Warranty Disclaimer of Unstated Warranties

CP322ia specifications

The BOXLIGHT CP322ia is an innovative interactive projector designed to enhance learning and collaboration in educational and corporate environments. This cutting-edge device seamlessly combines projection capabilities with interactive features, making it a versatile solution for classrooms and meeting rooms alike.

One of the standout features of the CP322ia is its impressive brightness, boasting a luminosity of 3,200 lumens. This high brightness level ensures that images and presentations remain clear and vibrant even in well-lit environments. Coupled with WXGA resolution (1280 x 800), the projector delivers sharp and detailed visuals, ensuring that every detail is visible during presentations or lessons.

The CP322ia utilizes advanced DLP (Digital Light Processing) technology, which provides excellent color accuracy and reliability. DLP technology enhances image quality and contributes to longer-lasting performance with minimal maintenance. Furthermore, the projector has a lamp life of up to 15,000 hours, significantly reducing the frequency of lamp replacements and lowering total cost of ownership.

A key feature of the BOXLIGHT CP322ia is its interactive capabilities. The projector incorporates touch technology, allowing users to interact directly with the projected image. This feature enables educators and presenters to engage their audience actively, facilitating collaborative learning experiences. The built-in software supports multiple users, allowing for simultaneous interaction, which is particularly useful for group activities.

Additionally, the CP322ia supports various connectivity options, including HDMI, USB, VGA, and built-in wireless capabilities. This versatility allows seamless integration with numerous devices such as laptops, tablets, and smartphones, making it easy to share content and connect with other technology in the workspace. The projector is also compatible with various teaching and presentation software, enhancing its functionality.

In terms of design, the CP322ia is compact and lightweight, making it easy to transport between different locations. The installation process is straightforward, and the projector features vertical keystone correction and manual zoom, allowing for quick adjustments to the image for optimal display quality.

In summary, the BOXLIGHT CP322ia is a powerful interactive projector that combines high brightness, advanced DLP technology, and engaging interactive capabilities to transform how presentations and lessons are delivered. With its diverse connectivity options, ease of use, and durable design, the CP322ia is an excellent choice for those seeking a reliable and effective projection solution.
Top Page Image Contents