BOXLIGHT CP-15t manual Lamp Replacement Indicator, Lamp Replacement Monitor Timer

Page 43

APPENDIX

LAMP REPLACEMENT Indicator

When the Lamp of the projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the image become dark or the color of the image becomes unnatural, replacement of the Lamp is required.

Lamp Replacement

CAUTION

For continued safety, replace with a lamp assembly of the same type.

Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace the lamp assembly.

1

Turn off the projector and disconnect the AC plug. Allow the

projector to cool for at least 45 minutes.

2

Remove the screw with a screwdriver and remove the lamp cover.

 

3

Remove 2 screws with a screwdriver and pull out the lamp

LAMP COVER

 

assembly by grasping the handle.

4

Replace the lamp assembly.

 

5

Replace the Lamp Assembly and tighten 2 screws. Make sure

 

that the Lamp Assembly is set properly. And replace the Lamp

 

 

Cover and tighten the screw.

 

6

on.Connect the AC Power Cord to the projector and turn the projector

 

7

Reset the Lamp Replacement Monitor Timer (refer to the section

 

 

“Lamp Replacement Monitor Timer” below.)

HANDLE

NOTE : Do not reset the LAMP REPLACEMENT MONITOR

TIMER, when the lamp was not been replaced.

LAMP ASSEMBLY

Lamp Replacement Monitor Timer

Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.

1

Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT

 

LEFT/RIGHT buttons to select SETTING

and press the SELECT button (refer to the page 40). Another

 

dialog box SETTING MENU Menu will appear.

 

2

Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Lamp age, and then press the

 

SELECT button. The message of "Lamp replace monitor Reset?" is displayed.

3

Select [Yes] to reset the Timer.

 

Do not reset the Lamp Replacement Monitor Timer, except after the lamp has been replaced.

Cleaning the Projection Lens

Follow these steps to clean the projection lens:

1

Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.

Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2

3

Lightly wipe the cleaning cloth over the lens.

When you are not using the projector, replace the lens cover.

43

Image 43
Contents Boxlight To the Owner Safety PrecautionsRisk of Electric Shock Do not Open Electrician. Do not defeat Important Safety InstructionsSafety purpose of this grounding Plug into the outlet, contact yourTable of Contents Compatibility Features and DesignName of Each Part of the Projector PreparationAdjustable Feet SETTING-UP the ProjectorPositioning the Projector Ventilation Preparation Connecting the AC Power CordProjector side Female AC outlet side Male Moving the Projector Terminals of the Projector Connecting the ProjectorConnecting the Projector Connecting to the Video EquipmentIBM-COMPATIBLE Computers VGA / Svga / XGA / Sxga Connecting to the IBM-COMPATIBLE ComputerControl Port Audio Audio OUT Monitor OUT MCI Serial Computer Audio Speaker Stereo Audio Amplifier Monitor Output Connection to the Macintosh ComputerDesktop type Monitor To the MonitorMode 1152 x Mode 640 xMode 832 x Mode 1024 xBefore Operation Operation of the Remote ControlLaser Pointer button Operating Range of the Remote Control Remote Control Batteries InstallationTOP Controls and Indicators Operating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Before Operation Menu BAR View Menu Used to adjust Position Size Image Refer to P36Turning off the Projector Basic OperationsTurning on / OFF the Projector Turning on the ProjectorPicture Freeze / no Show Function Adjusting the ImageZoom Adjustment Focus AdjustmentDirect Operation Sound AdjustmentMenu Operation Automatic Multiscanning system Computer ModeSelecting Computer Mode Selecting Computer SystemQuit PC AdjustmentReset StoredFreq Compatible Computer SpecificationsKHz Adjust Picture Image Manually Picture Image AdjustmentPosition Auto Image FunctionNormal Function NormalCompress function Picture Position AdjustmentPicture Screen Adjustment Expand functionSelecting Video Mode Video ModeSelecting Color System Wide Adjusting the Picture ImageColor Tint Contrast Brightness Sharpness RegularAvailable Data MCI ModeHow to Load a PC Card Into the Projector Operating the PC Card SlotIndex Selection MCI ModeShow the Data in the Memory Card Display Data on ScreenWill be displayed on the screen for a few seconds Box Write Data Into Memory Card Access to the Card with the ProjectorSmartmedia and PC Card Adapter Install / Remove the SmartMediaPC Card Adapter supplied SmartMedia supplied Eject button SmartMedia Precautions and Specifications of the appliancePC Card Adapter Setting Menu SettingSetting Language Appendix Operating Wireless MouseInstallation Controlling Wireless MouseTemperature Warning Indicator MaintenanceAIR Filter Care and Cleaning Cleaning the Projection Lens Lamp Replacement IndicatorLamp Replacement Lamp Replacement Monitor TimerProblem Try these Solution TroubleshootingRemote Control Technical Specifications Page Boxlight

CP-15t specifications

The BOXLIGHT CP-15t is a state-of-the-art educational tool designed to enhance the teaching and learning experience in classrooms and training environments. This interactive projector incorporates advanced technologies to provide educators with a versatile and user-friendly solution for presenting lessons, videos, and other educational materials.

One of the key features of the BOXLIGHT CP-15t is its impressive brightness level, which reaches up to 3,500 lumens. This high brightness ensures that the projected images remain vivid and clear, even in well-lit classrooms. With a native resolution of 1280 x 800 pixels, the projector delivers sharp and detailed visuals, making it ideal for displaying presentations, graphs, and educational content with precision.

The BOXLIGHT CP-15t utilizes DLP (Digital Light Processing) technology, which not only enhances image quality but also promotes longevity and reliability. DLP projectors are known for their high contrast ratios, ensuring that colors appear rich and vibrant, while black levels are deep. This results in a more engaging visual experience for both teachers and students.

Additionally, the CP-15t is equipped with a variety of connectivity options, including HDMI, VGA, USB, and audio inputs. This extensive range allows users to easily connect laptops, document cameras, tablets, and other devices, making it a highly adaptable tool for modern classrooms. The projector also supports wireless capabilities, enabling seamless streaming and sharing of content without the need for cumbersome cables.

Another standout feature of the BOXLIGHT CP-15t is its interactive capabilities. When paired with the right software, this projector can transform any flat surface into an interactive touchscreen. Teachers can write, draw, and annotate directly on the projected image, facilitating dynamic discussions and enhancing student engagement.

Furthermore, the CP-15t's compact and portable design makes it easy to transport between classrooms or training locations. Its long lamp life, which can extend up to 20,000 hours, ensures that the projector remains operational for an extended period, reducing maintenance costs and downtime.

In summary, the BOXLIGHT CP-15t is a remarkable interactive projector that combines high brightness, advanced DLP technology, versatile connectivity, and interactive features to create an innovative teaching tool. Its ability to deliver exceptional image quality and interactive engagement makes it a valuable asset for educators aiming to inspire and educate their students effectively.