BOXLIGHT CP-13t manual Appendix Lamp Replacement Indicator, Lamp Replacement Monitor Timer

Page 43

APPENDIX

LAMP REPLACEMENT INDICATOR

When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights red. When the image becomes dark or the color of the image become unnatural, replacement of the Lamp is required.

LAMP REPLACEMENT

CAUTION

● For continued safety, replace with a lamp assembly of the same type.

● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

●Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace the lamp assembly.

1

Turn off the projector and disconnect the AC plug. Allow the

 

projector to cool for at least 45 minutes.

 

2

Cover.Remove a screw with a screwdriver and remove the Lamp

 

3

Remove 2 screws with a screwdriver and pull out the Lamp

 

Assembly by grasping the handle.

 

4

Replace the Lamp Assembly with new one and tighten 2

LAMP COVER

 

screws. Make sure that the Lamp Assembly is set properly.

HANDLE

 

And replace the Lamp Cover and tighten a screw.

5

Connect the AC Power Cord to the projector and turn the

 

projector on.

 

6

Reset the Lamp Replacement Monitor Timer (refer to the

 

section “Lamp Replacement Monitor Timer” below).

 

NOTE : Do not reset the LAMP REPLACEMENT MONITOR

TIMER, when the lamp is not replaced.

LAMP

ASSEMBLY

 

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901. ● Model No. of your projector : BOXLIGHT CP-13t

●Replacement Lamp Type No. : POA-LMP21J

(Service Parts No. 610 280 6939)

LAMP REPLACEMENT MONITOR TIMER

Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.

1

Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT

 

LEFT/RIGHT buttons to select SETTING

and press the SELECT button (refer to the page 40). Another

 

dialog box SETTING MENU will appear.

 

2

Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to Lamp age, and then press the

 

SELECT button. The message "Lamp replace monitor Reset?" is displayed.

3

Select [Yes] to reset the Timer.

 

Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Boxlight To the Owner Safety PrecautionsRisk of Electric Shock Do not Open Ground Important Safety InstructionsTable of Contents Compatibility Features and DesignName of Each Part of the Projector PreparationAdjustable Feet SETTING-UP the ProjectorPositioning the Projector Ventilation Preparation Connecting the AC Power CordPreparation Moving the Projector Terminals of the Projector Connecting the ProjectorVideo Cable Connecting to the Video EquipmentConnecting the Projector Used cables for connectionVGA Cable Control Cable for PS/2 Port Connecting to the ComputerMAC Adapter Monitor Cable MAC Adapter Not supplied Computer Monitor Control Audio OUT PortBefore Operation Operation of the Remote ControlLaser Pointer Function Operating Range Remote Control Batteries InstallationTOP Controls and Indicators Operating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Before Operation Menu BAR View Menu Menu BAR in MCI ModeTurning OFF the Projector Basic OperationsTurning on / OFF the Projector Turning on the ProjectorZoom Adjustment Adjusting the ImageKeystone Adjustment Basic Operation No Show Function Sound AdjustmentSound Volume Adjustment Sound Mute AdjustmentSelecting Computer Mode Computer ModeSelecting Computer System Adjust PC AdjustmentClamp Total linesTotal dots Horizontal / VerticalKHz Computer Mode Compatible Computer SpecificationsResolution FreqNormal Function Adjust Picture Image ManuallyPosition Picture Position AdjustmentComputer Mode Auto Image Function Auto ImagePanning function Picture Screen AdjustmentExpand function Compress functionAuto Video ModeSelecting Video Mode Selecting Color SystemSharpness Adjusting the Picture ImageColor TintLoad MCI ModeHOW to Load the Memory Card Into the Projector Operating the PC Card SlotAvailable Data Selecting MCI ModeAvailable Card Index Selection Show the Data in the Memory CardSelection Write Data Into the Memory Card Access to the Memory Card Through the ProjectorAdjust the Picture Image Manually Picture Image AdjustmentImage Picture Screen Adjustment Remove Install / Remove the SmartmediaInstall Smartmedia and PC Card AdapterPrecautions and Specifications of the PC Card Adapter MCI Mode Precautions and Specifications of the SmartmediaSetting Menu SettingSelecting Language Appendix Operating Wireless MouseInstallation Operating Wireless MouseCleaning the Projection Lens MaintenanceTemperature Warning Indicator AIR Filter Care and CleaningLamp Replacement Appendix Lamp Replacement IndicatorLamp Replacement Monitor Timer Troubleshooting Function does not Remote Control UnitWireless Mouse Does not workTechnical Specifications Optional Parts Boxlight
Top Page Image Contents