Onkyo MD-105X To manually record a track number, To stop recording temporarily, To eject the MD

Page 27

Analog recording (continued)

Since the interval between tracks is detected based on the sound level, some tracks may not be numbered correctly in the following cases:

•Recorded condition of the cassette tape is bad (noise between tracks).

•Low sound level in quiet music.

•Interval between tracks is extremely shot.

•Tuner's reception is bad (noise).

To disable this function refer to the explanation below on this page.

To manually record a track number

While recording, press the o REC button when you wish to mark a track number.

If you wish to mark two or more track numbers sequentially, provide a sufficient interval between each press of the o REC button. Too short (about 4 seconds or less) an interval may lead to a failure in marking track numbers.

To stop recording temporarily...

Press the s/g button (or the g button on the remote controller). To resume recording, press the s/g button (or press the s button on the remote controller).

To stop recording...

Press the e STOP button.

To eject the MD...

Press the e STOP button, then the r EJECT button.

Note

If TOC is flashing when you press the r EJECT button or the STANDBY/ON button, it means the MD recorder is writing the recorded contents onto the MD. During this period, do not disconnect the power cord or apply strong vibrations to the MD recorder. Doing so may prevent normal recording onto the MD.

If the MD recorder's power cord is connected to the

SWITCHED service power outlet on the rear panel of your amplifier, etc., do not turn off the amplifier.

To disable the automatic track numbering

function...

Perform the following steps while you are recording or waiting for the recording to start:

EDIT/NO

DIGITAL IN 1

L

 

 

 

 

 

1

2

3

4

5

 

40

20

10

6

2

0

6

7

8

9

10

 

R

 

 

 

 

 

11

12

13

14

15

15

1.Press the EDIT/NO button. "LevelSync?" appears on the display.

2.Press the YES button.

YES

DIGITAL IN 1

L

 

 

 

 

 

1

2

3

4

5

 

40

20

10

6

2

0

6

7

8

9

10

 

R

 

 

 

 

 

11

12

13

14

15

15

If the function is currently turned on. "On Off? "appears on the display.

3.Press the YES button.

"LvlSyncOff" appears on the display.

YES

DIGITAL IN 1

L

 

 

 

 

 

1

2

3

4

5

 

40

20

10

6

2

0

6

7

8

9

10

 

R

 

 

 

 

 

11

12

13

14

15

15

Now the tracks will not be numbered during recording.

•Press the EDIT/NO button any time if you wish to cancel the setting.

To enable the automatic track numbering function...

Perform the following steps while you are recording or waiting for the recording to start:

•Press the EDIT/no button.

"Level Sync?" appears on the display.

•Press the YES button.

If the function is currently turned off, "Off On?" appears on the display.

•Press the YES button.

Operations

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents MD-105X Before using ConnectionsThank you for purchasing Main FeaturesPower-Cord Protection Power-supply Before UsingPrecautions Precautions Laser is covered by a housing which preventsFor U.S. model For British model For Canadian modelModele pour les Canadien For European modelChecking the supplied accessories Table of contentsReplace the compartment cover Using the remote controllerInserting the remote controller batteries Using the remote controllerUsing the remote controller Direct Change Auto Power OnRemote control of the System Components Program Timer Sleep Timer CD-dubbingBefore connecting Connecting to the other componentsConnection with the Amplifier Connection to the Digital Input Terminals Digital Input 1Connection to AC outlet Tuner Amplifier MD-105X Cable CD player Connecting to the other componentsConnecting the z controller Connecting the AC power cord mains leadRC-409MD supplied RC-398S supplied Standby indicator goes outNormal play Insert an MDNormal play Changing the display modeTurn the Amcs knob clockwise or press RC-409MD RC-398STo select the 100th track 25 + 25 + 1 + 10 + To play the next track or a later trackSearching for a part to play by sound at play Music ScanSearching for a part to play Search play RC-409MDsuppliedWith RC-409MDsupplied RC-398SsuppliedRC-398S supplied with the A-905X amplifier Repeat playTo stop the Repeat play RC-409MDsupplied RC-398Ssupplied with A-905XTo stop A-B Repeat Repeat playRC-409MDsupplied RC-398Ssupplied With To exit the Memory play modeChecking the stored contents Memory playController To select a track numbered 26 or above using RC-409MDTo select a track numbered 11 or above using RC-398S Memory playLoad the CD in the CD player CD-dubbing System operationCD-dubbing System operation Load recordable MD in the MD105XCD-dubbing with track specified CD-dubbing System operationSet the Input selector to Analog MO or ST position Analog recordingPress the STANDBY/ON button Load a recordable MDUsing the Amcs knob, adjust the recording level Analog recordingPress the oREC button To stop recording temporarily To disable the automatic track numbering FunctionTo enable the automatic track numbering function To manually record a track numberPress the STAND-BY/ON button Digital recordingUsing the Amcs knob, adjust Digital recordingRecording level Signal Wait function Press the e buttonPress the e button and then the r Eject button Signal Synchro recording Press the REC button twice to display Signal RecRecording starts To stop CD-synchro recording Set the MD recorder to the recording standby modeSystem operation CD-synchro recordingSystem operation To stop synchro recordingStart playing the cassette deck Synchro-recording from MD to cassette deck RC-409MD supplied RC-398S supplied with 905XTo stop synchro recording Set the Input selector to ST stereo position Timer operationSet the timer on your T-405X Power switch of the A-905XProtecting recordings from accidental erasure Checking the contents of recordingStorage period of backup data Other information for recordingEditing the contents of an MD Editing the contents of an MD Press the YES button again Combining tracksPress the EDIT/NO button several Times until Combine ? appears in the displayPress the YES button to combine the tracks you have selected Moving a track Press the YES button to move the selected trackTo stop moving a track To name a track Select the character input mode using the Display buttonNaming a track or disc To name a discNaming a track or disc Enter a track name or disc name using the Amcs knobErasing the disc name and all track names at one time Preset titles for easy titlingSelect Undo? Canceling the last editingUndo function Undo the last editingMessage Meaning Message listSystem limitations 60, 74 or 80 minutesSome tracks cannot be combined with others Rules for digital recording Guide to the serial copy management systemRule Symptom Cause Remedy TroubleshootingUsed TroubleshootingSymptom Cause CondensationRemoving the halfway inserted MD Precautions for handling the MiniDisc MDStorage location Regular careIndexed to parts and controls Front panelDisplay Remote controller RC-409MD supplied Power buttonIndexed to parts and controls Supplied with the A-905X amplifier RC-398SMemo Specifications

MD-105X specifications

The Onkyo MD-105X is a high-performance MiniDisc player that embodies the elite standards of audio reproduction with a rich array of features and innovative technologies. Designed with audio enthusiasts in mind, the MD-105X offers superior sound quality, compact design, and versatile functionality, making it an ideal choice for both casual listeners and serious audiophiles.

One of the standout features of the Onkyo MD-105X is its MDLP (MiniDisc Long Play) capability, which allows users to record and playback audio in a compressed format, extending the recording time significantly. With this technology, users can store up to 320 minutes of audio on a single MiniDisc, a substantial increase compared to standard MiniDisc recording times. This flexibility caters to users who require lengthy playback without sacrificing audio quality, making it perfect for long events or extended listening sessions.

The player is equipped with a high-quality digital-to-analog converter (DAC) that ensures precise audio reproduction. This module is crucial for converting digital signals from the MiniDisc into analog sounds that can be enjoyed through speakers or headphones. With this level of sound processing, the MD-105X delivers rich, detailed audio that captures the nuances of recordings, making every listening experience truly immersive.

Furthermore, the Onkyo MD-105X features an intuitive user interface that simplifies navigation through its extensive features. It includes direct track access, programmable playback options, and a clear LCD display that provides essential information such as track numbers and remaining recording time. Users can customize their listening experience with variable playback speeds and an array of EQ settings designed to optimize sound quality based on personal preferences.

Connectivity options are also a highlight of the MD-105X. The player includes optical and coaxial digital outputs, allowing users to connect directly to digital audio receivers for a high-quality audio experience. This functionality ensures seamless integration into existing home theater systems, making it a versatile component for audiophiles.

In conclusion, the Onkyo MD-105X stands out in the realm of MiniDisc players, combining advanced technologies, user-friendly features, and superior audio performance. Its MDLP compatibility, high-quality DAC, and comprehensive connectivity options set it apart as a reliable choice for those who appreciate the art of sound and the convenience offered by MiniDisc technology. As portable media continues to evolve, the Onkyo MD-105X serves as a worthy companion for high-fidelity audio enthusiasts.
Top Page Image Contents