BenQ MP770 user manual Lamp indicator light, Auto

Page 13

7.MODE

Depending upon which input signal is selected, selects an available picture setup mode. See "Application Mode" on page 48 for details.

When a wireless module is installed and the Wireless Connection menu is displayed, press this button to change among LAN, IEEE 802.11 a, and IEEE 802.11 b/g. (The wireless module is available through BenQ retailers.)

8.BLANK

Used to hide the screen image. To restore the image, press any button (except LASER) on the projector or remote control. See "Hiding the image" on page 40 for details.

9.ENTER

Enacts the selected On-Screen Display (OSD) menu item. See "Using the menus" on page 46 for details.

10.Temperature warning light Lights up red if the projector's temperature becomes too high. See "Indicators" on page 60 for details.

11.Lamp indicator light

Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem. See "Indicators" on page 60 for details.

12.AUTO

Automatically determines the best picture timings for the displayed image. See "Auto-adjusting the image" on page 35 for details.

When a wireless module is installed, the Wireless Connection menu is displayed and the IEEE 802.11 a is selected, press this button to search for a reliable channel. (The wireless module is available through BenQ retailers.)

13.SOURCE

Sequentially selects the input signal D- Sub (Analog RGB), Comp. (YPbPr), DVI-A, DVI-D, Video, or S-Video. See "Switching input signal" on page 34 for details.

Introduction 13

Image 13
Contents Welcome Disclaimer CopyrightTable of contents Troubleshooting Specifications Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Bedding or any other soft surface 10000 Feet Important safety instructionsSafety Instructions Introduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear side Projector Controls and functionsAuto Lamp indicator lightRemote control PIP LED indicator lightMode MuteRemote control batteries Remote control effective rangeFront Rear Choosing a location Positioning your projectorSafety instructions for ceiling mounting of the projector Obtaining a preferred projected image size Page Projection dimensions Connecting a computer or monitor Wireless connection optionalConnection Cable connectionVGA Socket, not the DVI-I socket With a VGA cable With a VGA to DVI-A cableBest video quality Connecting Video source devicesBetter video quality Least video qualityConnecting Audio Connecting a DVI source deviceDVI-D or DVI-I cable Audio Audio Cable cable AV device1080i 50/ 60 Hz To connect the projector to an S-Video source device Connecting an S-Video source deviceConnecting a composite Video source device Start up OperationOperation Setting a password Utilizing the password functionIf you forget the password Up , Right, Down, Left respectivelyChanging the password Entering the password recall procedureDisabling the password function Adjusting the projected image Switching input signalAdjusting the projection angle Remote control. a source selection bar displays. YouFine-tuning the image size and clarity Auto-adjusting the imageSearching for details on the projected image Correcting keystoneYou are satisfied with the shape Control. Go to the Display Keystone menuSelecting the aspect ratio Setting the User 1/User 2 mode Selecting an application modeGo to the Picture Application Mode menu Optimizing the imageAdjusting brightness Fine-tuning the image quality in user modesAdjusting contrast Selecting a color temperatureOperating in a high altitude environment Other adjustmentsHiding the image PIP Picture In Picture operation Freezing the image Remote paging operationsCreating your own startup screen Shutting down the projector Personalizing the projector menu displayPress Message will disappearMenu system Menu operationPC source Brightest Video source Cinema/MovieBasic Information ResolutionAdvanced Use Left/ Right to select the Display menu Using the menusDisplay menu Picture menu Source menu System setup Basic menu System setup Advanced menu Lamp Timer Mode ResolutionInformation menu SourceCare of the projector MaintenanceClean the Air Filter To clean the filterCheck the Air Filter Replacing the filter spongeCalculation of lamp hour Lamp informationOut of Lamp Usage Time Replacing the lampPage Tighten the screw that secures the lamp Temperature informationRestart the projector Stand-by mode IndicatorsPowering up IllustrationLight Status & Description Power Temp Lamp Thermal events Make sure that it is switched on Plug the power cord into the AC inlet onRemote mouse function does not work Projector specifications SpecificationsSupported timing for PC including DVI-I input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsMm W x 94 mm H x 230 mm D 298 Unit mm Specifications DimensionsLimited warranty WarrantyFCC statement Regulation statementsEEC statement MIC statement
Related manuals
Manual 68 pages 9.95 Kb