BenQ ms616st, mx618st user manual Switching input signal, Changing Color Space

Page 23

Press to highlight Power On Lock and press / to select Off. You will not have to enter the password next time when turning on the projector.

ii.If the password is incorrect, the password error message appears lasting for three seconds, and the message “INPUT PASSWORD” appears for your retry. You can press MENU/EXIT to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

To select the source:

1.Press SOURCE on the projector or remote control. A source selection bar appears.

2.Press / until your desired signal is selected and press MODE/ENTER.

Once detected, the selected source information will display at the corner of the screen for seconds. If there is multiple equipment connected to the projector, repeat steps 1-2to search for another signal.

•The brightness level of the projected image will change accordingly when you switch between different input signals. Data (graphic) "PC" presentations using mostly static images are generally brighter than "Video" using mostly moving images (movies).

•The native display resolution of this projector is in a 4:3 aspect ratio. For best display picture results, you should select and

use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See "Selecting the aspect ratio" on page 24 for details.

Changing Color Space

In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV.

To do this:

1.Press MENU/EXIT and then press / until the SOURCE menu is highlighted.

2.Press to highlight Color Space Conversion and press / to select a suitable

color space.

This function is only available when the HDMI-input port is in use.

Operation 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents MS616ST/MX618ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsRemote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableLength Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm Diagonal MinConnection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionFreezing the image Remote paging operationsOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneUsing the test pattern To select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Display menu Picture menu Function Description 3D Sync Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsQuick SplashScreen Auto BlankStandby Reset AllClosed CaptionCare of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Troubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsKHz Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents