BenQ ms616st, mx618st Positioning your projector, Choosing a location, Front Table, Front Ceiling

Page 13

Positioning your projector

Choosing a location

Your projector is designed to be installed in one of four possible installation locations:

1.Front Table

Select this location with the projector placed on the table in front of the screen. This is the most common way to position the projector for quick setup and portability.

2.Front Ceiling

Select this location with the projector suspended upside-down from the ceiling in front of the screen.

Purchase the BenQ Projector Ceiling Mount Kit from your dealer to mount your projector on the ceiling.

Set Front Ceiling in the SYSTEM SETUP: Basic > Projector Position menu after you turn the projector on.

3.Rear Ceiling

Select this location with the projector suspended upside-down from the ceiling behind the screen.

Note that a special rear projection screen and the BenQ Projector Ceiling Mount Kit are required for this installation location.

Set Rear Ceiling in the SYSTEM SETUP: Basic > Projector Position menu after you turn the projector on.

4.Rear Table

Select this location with the projector placed on the table behind the screen.

Note that a special rear projection screen is required.

Set Rear Table in the SYSTEM SETUP: Basic > Projector Position menu after you turn the projector on.

Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

Positioning your projector

13

Image 13

Contents MS616ST/MX618ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsRemote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal Min LengthConnection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature 3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Remote paging operationsHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundUsing the test pattern To select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description 3D SyncTimer System Setup Basic menu Function Description Quick AutoSettings SearchScreen SplashAuto Blank QuickClosed Reset AllCaption StandbyCare of the projector MaintenanceGetting to know the lamp hour Lamp informationExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Light Status & Description Power events IndicatorsLamp events Troubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Limited warranty Warranty and Copyright informationCopyright Disclaimer