BenQ ms616st Setting the presentation timer, To cancel the timer, perform the following steps

Page 29

6.Press to highlight Gain and adjust its values to your preference by pressing /

. The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.

7.Repeat steps 3 to 6 for other color adjustments.

8.Make sure you have made all of the desired adjustments.

9.Press MENU/EXIT to exit and save the settings.

Setting the presentation timer

Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1.Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/ENTER to display the Presentation Timer page.

2.Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-minute increments.

If the timer is already on, the timer will restart whenever the Timer Period is reset.

3.Press to highlight Timer Display and choose if you want the timer to show up on the screen by pressing / .

Selection

Description

Always

Displays the timer on screen throughout the presentation time.

3 min/2 min/1 min

Displays the timer on screen in the last 3/2/1 minute(s).

Never

Hides the timer throughout the presentation time.

4.Press to highlight Timer Position and set the timer position by pressing / .

Top-Left Bottom-Left Top-Right Bottom-Right

5.Press to highlight Timer Counting Direction and select your desired counting direction by pressing / .

Selection

Description

Count Up

Increases from 0 to the preset time.

Count Down

Decreases from the preset time to 0.

6.Press to highlight Sound Reminder and decide if you want to activate sound

reminder by pressing / . If you select On, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.

7.To activate the presentation timer, press and press / to highlight On and press MODE/ENTER.

8.A confirmation message appears. Highlight Yes and press MODE/ENTER on the projector or remote control to confirm. You will see the message “Timer is On” displaying on the screen. The timer starts counting when the timer is on.

To cancel the timer, perform the following steps:

1.Go to the SYSTEM SETUP: Basic > Presentation Timer menu and highlight Off. Press MODE/ENTER. A confirmation message appears.

Operation 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents MS616ST/MX618ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsRemote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal Min LengthConnection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Remote paging operationsHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundUsing the test pattern To select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description 3D SyncTimer System Setup Basic menu Function Description Quick AutoSettings SearchScreen SplashAuto Blank QuickClosed Reset AllCaption StandbyCare of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Troubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsKHz Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer
Top Page Image Contents