BenQ ms616st Display menu Picture menu Function Description 3D Sync, Invert, Teaching, Template

Page 41

1. DISPLAY menu

2. PICTURE menu

Function

Description

3D Sync

When you discover the inversion of the image depth, enable this

Invert

function to correct the problem.

 

 

 

Teaching

See "Using the teaching templates" on page 34 for details.

Template

 

 

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 26 for details.

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 26

 

for details.

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on

page 27 for details.

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 27 for details.

 

 

Adjusts the color saturation level -- the amount of each color in a

Color

video image. See "Adjusting Color" on page 27 for details.

This function is only available when a Video, S-Video or Component Video

 

 

signal is selected.

 

 

 

Adjusts the red and green color tones of the image. See "Adjusting

Tint

Tint" on page 27 for details.

This function is only available when a Video or S-Video signal is selected and

 

 

the system format is NTSC.

 

 

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 27 for details.

This function is only available when a Video, S-Video or Component Video

 

 

signal is selected.

 

 

Brilliant Color

See "Adjusting Brilliant Color" on page 27 for details.

 

 

Color

See "Selecting a Color Temperature" on page 27 for details.

Temperature

 

 

3D Color

See "3D Color Management" on page 28 for details.

Management

 

 

 

Save Settings

Saves the settings made for User 1 or User 2 mode.

 

 

Operation 41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents MS616ST/MX618ST Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsRemote control Replacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal Min LengthConnection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuSelecting a Color Temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color 3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Remote paging operationsHiding the image To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundUsing the test pattern To select Blackboard or Whiteboard Using the teaching templatesPresenting from a USB Reader Shutting down the projector Direct power offMain menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description 3D SyncTimer System Setup Basic menu Function Description Quick AutoSettings SearchScreen SplashAuto Blank QuickClosed Reset AllCaption StandbyCare of the projector MaintenanceExtending lamp life Lamp informationGetting to know the lamp hour Status Message Timing of replacing the lampReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Troubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsKHz Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer
Top Page Image Contents