BenQ W1080ST, W1070 Connecting component-video devices, Connecting S-Video or video devices

Page 22

Connecting component-video devices

Be sure to match the corresponding colors between the cables and the terminals. The RCA type component video jacks are provided for connection to video output devices. You should also connect the separate audio cable to a suitable audio amplifier.

AV equipment: DVD player, digital

tuner, etc.

From audio output	To audio input
terminals	terminals

Component video cable

Connecting S-Video or video devices

You need only connect S-Video or composite Video cable from the same device, never both at the same time. You should also connect the separate audio cable to a suitable audio amplifier.

AV equipment	From audio output To audio input terminals
	terminals

S-Video cable

or

Video cable

• If you have already made a Component Video connection between the projector and the video source device, you need not connect to this device again using an S-Video or composite Video connection as this makes an unnecessary second connection of poorer picture quality. You need only connect using a composite Video connection if both Component Video and S-Video are not supplied on the video source device (for example, with some analog video cameras).

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, please check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

22 Positioning your projector

Image 22

Contents W1070/W1080ST Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control effective range Replacing the remote control batteriesCeiling mounting the projector Overview Projector features Rear and lower side view Projector exterior viewFront and upper side view Control panel See Control panel on page 11 for detailsControl panel Controls and functionsFocus ring Remote control Choosing a location Positioning your projectorFront Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Positioning your projector Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D mm Screen dimensions Projection distance D Lowest Highest Installation for a 43 ratio screenFloor Installation Ceiling Installation ImageFor assistance Shifting the projection lens vertically To use the lens shift leverConnecting Hdmi devices Connecting with video equipmentPreparations Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on Using the projectorPreparations Selecting an input source Fine-tuning the image size and claritySharpen the picture by rotating the focus ring Use / to highlight the System Setup Basic menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password Highlight Change Password and press MODE/ENTER.Disabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Fine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode Setting the User 1/User 2/User 3 modeAdjusting Brightness Fine-tuning the picture qualityResetting the picture mode Adjusting ContrastAdjusting Sharpness Adjusting TintSelecting a color temperature Selecting a Gamma setting Setting Black LevelSetting a preferred color temperature Advanced picture quality controlsHighlight Primary Color and press / to select a color from Adjusting Brilliant ColorColor Management Among Red, Green, Blue, Cyan, Magenta and YellowSetting 3D Comb Filter Adjusting the soundSetting Film Mode Adjusting the sound levelSelecting the aspect ratio About the aspect ratioMagnifying and searching for details To activate High Altitude ModeOperating in a high altitude environment Using the 3D menus Watching 3D contentConnecting 3D video devices PlayStation gamesTurning the projector off Personalizing the projector menu displayLocking control keys To lock the keysOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Advanced System SetupBasic InformationFunction Description Overscan Adjustment VolumePower On/Off Ring PC & Component YPbPr TuningLanguage Sleep TimerMenu Settings Splash ScreenHigh Altitude Mode Lamp SettingsHdmi Settings PasswordSource Reset All SettingsResolution Color SystemAdditional information Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Replacing the lamp Timing of replacing the lampStatus Message Using the projector Resetting the lamp timer Connect the power and restart the projectorIndicators Power Temp Lamp Status & DescriptionYour Blu-ray Disc is not in 3D TroubleshootingProblem Cause Remedy FormatSpecifications Dimensions 311.87 244.12 Unit mmRefresh rate Frequency Pixel Format Timing chartSupported timing for PC input KHzSXGA60 60.020 63.981 108.000 Supported timing for Hdmi Hdcp input 66.667 35.000 30.240 832x624@75Hz Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationWarranty Disclaimer