BenQ Comprehensive Guide to Password Management for Projectors

Page 28

Entering the password recall procedure

1.Make sure the Input Password page displays on screen. Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen.

2.Write down the number and turn off your projector.

3.Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

RECALL PASSWORD

Please write down the recall code, and contact BenQ

Customer Center.

Recall code:

XXX XXX XXX XXX

Exit

Changing the password

1.Press MENU/EXIT on the projector or remote control and then press / until the System Setup : Advanced menu is highlighted.

2.Press / to highlight Password and press MODE/ENTER. The Password page displays.

3.Highlight Change Password and press MODE/ENTER. The Input Current Password page displays.

4.Enter the old password.

If the password is correct, the message "Input New Password" displays.

If the password is incorrect, the password error message displays lasting for three seconds, and the message "Input Current Password" displays for your retry. You can either press MENU/ EXIT to cancel the change or try another password.

5.Enter a new password.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

6.Confirm the new password by re-entering the new password.

7.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

8.To leave the OSD menu, press MENU/EXIT.

Disabling the password function

To disable password protection, go back to the System Setup : Advanced > Password > Password menu. Highlight Power On Lock and then press / to select Off. The message "Input Current Password" displays. Enter the current password.

If the password is correct, the OSD menu returns to the Password page with "Off" shown in the row of Power On Lock. You will not have to enter the password next time when turning on the projector.

If the password is incorrect, the password error message displays lasting for three seconds, and the message "Input Current Password" displays for your retry. You can either press MENU/ EXIT to cancel the change or try another password.

Note that though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

28 Using the projector

Image 28
Contents W1070/W1080ST Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control effective range Replacing the remote control batteriesCeiling mounting the projector Overview Projector features Projector exterior view Front and upper side viewRear and lower side view Control panel See Control panel on page 11 for detailsControl panel Controls and functionsFocus ring Remote control Choosing a location Positioning your projectorFront Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Positioning your projector Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D mm Installation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest ImageFor assistance Shifting the projection lens vertically To use the lens shift leverConnecting Hdmi devices Connecting with video equipmentPreparations Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on Using the projectorPreparations Selecting an input source Fine-tuning the image size and claritySharpen the picture by rotating the focus ring Using the menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Highlight Change Password and press MODE/ENTER.Entering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeFine-tuning the picture quality Resetting the picture modeAdjusting Brightness Adjusting ContrastAdjusting Sharpness Adjusting TintSelecting a color temperature Setting Black Level Setting a preferred color temperatureSelecting a Gamma setting Advanced picture quality controlsAdjusting Brilliant Color Color ManagementHighlight Primary Color and press / to select a color from Among Red, Green, Blue, Cyan, Magenta and YellowAdjusting the sound Setting Film ModeSetting 3D Comb Filter Adjusting the sound levelSelecting the aspect ratio About the aspect ratioMagnifying and searching for details To activate High Altitude ModeOperating in a high altitude environment Watching 3D content Connecting 3D video devicesUsing the 3D menus PlayStation gamesPersonalizing the projector menu display Locking control keysTurning the projector off To lock the keysOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options System Setup BasicAdvanced InformationFunction Description Volume Power On/Off RingOverscan Adjustment PC & Component YPbPr TuningSleep Timer Menu SettingsLanguage Splash ScreenLamp Settings Hdmi SettingsHigh Altitude Mode PasswordReset All Settings ResolutionSource Color SystemAdditional information Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Replacing the lamp Timing of replacing the lampStatus Message Using the projector Resetting the lamp timer Connect the power and restart the projectorIndicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications Dimensions 311.87 244.12 Unit mmTiming chart Supported timing for PC inputRefresh rate Frequency Pixel Format KHzSXGA60 60.020 63.981 108.000 Supported timing for Hdmi Hdcp input 66.667 35.000 30.240 832x624@75Hz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty and Copyright information WarrantyCopyright Disclaimer