BenQ W1080ST, W1070 Reset All Settings, Source, Resolution, Color System, Equivalent Lamp, Hour

Page 46

Reset All Settings	Returns all settings to the factory preset values.
Reset All Settings	The following settings will still remain: Keystone, Language, Projector
	Position, High Altitude Mode, Password, Key Lock, and ISF.
	The ISF calibration menu is password protected and only accessible by
	authorized ISF calibrators. The ISF (Imaging Science Foundation) has developed
	carefully crafted, industry-recognized standards for optimal video performance
ISF	and has implemented a training program for technicians and installers to use
ISF	these standards to obtain optimal picture quality from BenQ video display
	devices. Accordingly, we recommend that setup and calibration be performed
	by an ISF certified installation technician.
	For more information, please go to www.imagingscience.com or
	contact the place you purchased the projector.

Information menu

This menu shows you the current operating status of the projector.

Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on the screen.

	Function	Description
	Source	Shows the current signal source.

	Preset Mode	Shows the selected mode in the Picture > Preset Mode menu.

	Resolution	Shows the native resolution of the input source.

	Color System	Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.

	Equivalent Lamp	Shows the total lamp time used.
	Hour	Shows the total lamp time used.
	Hour

	3D Format	Shows the current 3D mode.
	3D Format	3D Format is only available when 3D Mode is enabled.
		3D Format is only available when 3D Mode is enabled.

	Firmware Version	Shows the firmware version of your projector.

46 Using the projector

Image 46

Contents W1070/W1080ST Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control effective range Replacing the remote control batteriesCeiling mounting the projector Overview Projector features Rear and lower side view Projector exterior viewFront and upper side view Control panel See Control panel on page 11 for detailsControl panel Controls and functionsFocus ring Remote control Choosing a location Positioning your projectorFront Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Positioning your projector Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D mm Screen dimensions Projection distance D Lowest Highest Installation for a 43 ratio screenFloor Installation Ceiling Installation ImageFor assistance Shifting the projection lens vertically To use the lens shift leverConnecting Hdmi devices Connecting with video equipmentPreparations Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on Using the projectorPreparations Selecting an input source Fine-tuning the image size and claritySharpen the picture by rotating the focus ring Use / to highlight the System Setup Basic menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password Highlight Change Password and press MODE/ENTER.Disabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Fine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode Setting the User 1/User 2/User 3 modeAdjusting Brightness Fine-tuning the picture qualityResetting the picture mode Adjusting ContrastAdjusting Sharpness Adjusting TintSelecting a color temperature Selecting a Gamma setting Setting Black LevelSetting a preferred color temperature Advanced picture quality controlsHighlight Primary Color and press / to select a color from Adjusting Brilliant ColorColor Management Among Red, Green, Blue, Cyan, Magenta and YellowSetting 3D Comb Filter Adjusting the soundSetting Film Mode Adjusting the sound levelSelecting the aspect ratio About the aspect ratioMagnifying and searching for details To activate High Altitude ModeOperating in a high altitude environment Using the 3D menus Watching 3D contentConnecting 3D video devices PlayStation gamesTurning the projector off Personalizing the projector menu displayLocking control keys To lock the keysOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Advanced System SetupBasic InformationFunction Description Overscan Adjustment VolumePower On/Off Ring PC & Component YPbPr TuningLanguage Sleep TimerMenu Settings Splash ScreenHigh Altitude Mode Lamp SettingsHdmi Settings PasswordSource Reset All SettingsResolution Color SystemAdditional information Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Replacing the lamp Timing of replacing the lampStatus Message Using the projector Resetting the lamp timer Connect the power and restart the projectorIndicators Power Temp Lamp Status & DescriptionYour Blu-ray Disc is not in 3D TroubleshootingProblem Cause Remedy FormatSpecifications Dimensions 311.87 244.12 Unit mmRefresh rate Frequency Pixel Format Timing chartSupported timing for PC input KHzSXGA60 60.020 63.981 108.000 Supported timing for Hdmi Hdcp input 66.667 35.000 30.240 832x624@75Hz Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationWarranty Disclaimer