BenQ W1080ST, W1070 user manual Using the projector, Turning the projector on, Preparations

Page 24

Using the projector

Preparations

1. Plug in and turn all of the connected equipment on.

2. If not already in, plug the supplied power cable into the AC inlet on the rear of the projector.

3. Plug the power cable into a wall power outlet and turn the wall switch on.

Please use the original accessories (e.g. power cable) only with the device to avoid possible dangers such as electric shock and fire.

Turning the projector on

Follow the steps below.

1.Make sure the Power light is orange after power has been applied.

2.Press and hold POWER () to turn the projector on. As soon as the lamp lights up, a "Power On Tone" will be heard. The POWER indicator light flashes green and stays green when the projector is on.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 35 for details.

3.The fans will start operating, and a start-up image displays on the screen for a few seconds while it warms up.

The projector will not respond to further commands while it is warming up.

4.If you are prompted for a password, press the arrow keys to enter a six-digit password. See "Utilizing the password function" on page 27 for details.

5."Source Searching..." will be displayed on the screen before the projector identifies the input source. This message will remain on the screen until a valid signal is detected. See "Selecting an input source" on page 25 for details.

6.If the horizontal frequency of the input source exceeds the range of the projector, the message "No Signal" will be displayed on the screen. This message will remain on-screen until you change the input source to an appropriate one.

24 Using the projector

Image 24

Contents W1070/W1080ST Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewReplacing the remote control batteries Remote control effective rangeCeiling mounting the projector Overview Projector features Projector exterior view Front and upper side viewRear and lower side view Control panel See Control panel on page 11 for detailsControls and functions Control panelFocus ring Remote control Positioning your projector Choosing a locationFront Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Positioning your projector Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D mm Installation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest ImageFor assistance Shifting the projection lens vertically To use the lens shift leverConnecting with video equipment Connecting Hdmi devicesPreparations Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableUsing the projector Turning the projector onPreparations Fine-tuning the image size and clarity Selecting an input sourceSharpen the picture by rotating the focus ring Using the menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Highlight Change Password and press MODE/ENTER.Entering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeFine-tuning the picture quality Resetting the picture modeAdjusting Brightness Adjusting ContrastAdjusting Tint Adjusting SharpnessSelecting a color temperature Setting Black Level Setting a preferred color temperatureSelecting a Gamma setting Advanced picture quality controlsAdjusting Brilliant Color Color ManagementHighlight Primary Color and press / to select a color from Among Red, Green, Blue, Cyan, Magenta and YellowAdjusting the sound Setting Film ModeSetting 3D Comb Filter Adjusting the sound levelSelecting the aspect ratio About the aspect ratioTo activate High Altitude Mode Magnifying and searching for detailsOperating in a high altitude environment Watching 3D content Connecting 3D video devicesUsing the 3D menus PlayStation gamesPersonalizing the projector menu display Locking control keysTurning the projector off To lock the keysOn-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup BasicAdvanced InformationFunction Description Volume Power On/Off RingOverscan Adjustment PC & Component YPbPr TuningSleep Timer Menu SettingsLanguage Splash ScreenLamp Settings Hdmi SettingsHigh Altitude Mode PasswordReset All Settings ResolutionSource Color SystemAdditional information Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Replacing the lampStatus Message Using the projector Resetting the lamp timer Connect the power and restart the projectorIndicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications Dimensions 311.87 244.12 Unit mmTiming chart Supported timing for PC inputRefresh rate Frequency Pixel Format KHzSXGA60 60.020 63.981 108.000 Supported timing for Hdmi Hdcp input 66.667 35.000 30.240 832x624@75Hz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty and Copyright information WarrantyCopyright Disclaimer