BenQ W1500 user manual Using the preset and user modes, Selecting a preset mode

Page 29

Using the preset and user modes

Selecting a preset mode

The projector is preset with several pre-defined picture modes so that you can choose one to suit your operating environment and input source picture type.

To select a preset mode that suits your need:

1.Press MENU/EXIT and then press / until the Picture -- Basic menu is highlighted.

2.Press to highlight Preset Mode.

3.Press / until your desired mode is selected.

These modes consist of preset values suitable for various projection situations as described below:

Cinema: With well-balanced color saturation and contrast with a low brightness level, this is most suitable for enjoying movies in a totally dark environment (as you would find in a commercial cinema).

Dynamic: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.

Standard: It is slightly brighter than Cinema mode, and suitable for use in rooms where there is a small amount of ambient light.

3D: It is optimized to bring up 3D effects when watching 3D contents.

This mode is only available when 3D function is enabled.

User 1/User 2/User 3: Recalls the customized settings. See "Setting the User 1/User 2/User 3 mode" on page 29 for details.

Fine-tuning the selected picture mode

The pre-defined picture mode settings can be altered via the available items shown in the Picture -- Basic menus.

To fine-tune the picture mode:

1.Press MENU/EXIT and then press / until the Picture -- Basic menu is highlighted.

2.Press to highlight the item you want to adjust and press / to set your desired value. Your selection is automatically stored in the projector and associated with that input source.

See "Fine-tuning the picture quality" on page 30 and "Advanced picture quality controls" on page 32 for details.

Each time you change the picture mode, the projector also changes the setting to the one which was last set for that particular picture mode on that particular input. If you change the input source, the most recently used picture mode and settings for that input and resolution will be restored.

Setting the User 1/User 2/User 3 mode

There are three user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the selected User mode) as a starting point and customize the settings.

1.In the Picture -- Basic menu, highlight Preset Mode and press / to select User 1, User 2, or User 3 mode.

2.Press to highlight User Mode Management.

This function is only available when User 1, User 2, or User 3 mode is selected up in the Preset Mode sub-menu item.

3.Press MODE/ENTER to display the User Mode Management page.

4.Press to highlight Reference Mode and press MODE/ENTER.

Important safety instructions

29

Image 29
Contents W1500 Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Disposal Moisture condensationAvoid volatile liquids Overview Shipping contentsCeiling mounting the projector Replacing the remote control batteriesRemote control effective range Important safety instructions Projector features Front and upper side view Rear and lower side view Projector exterior viewRS-232 control port Audio L/R input jacksControl panel Controls and functionsRemote control Front Choosing a locationFront Ceiling RearDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeImportant safety instructions Installation for a 169 ratio screen Projection dimensionsFloor Installation Ceiling Installation Installation for a 43 ratio screenScreen aspect ratio is 43 and the projected picture is Lowest HighestTo use the lens shift lever Shifting the projection lens verticallyTerminal appearance Reference PreparationsName ComponentConnecting Hdmi devices Connecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Turning the projector onSharpen the picture by rotating the focus ring Selecting an input sourceUsing a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password As the picture indicates, the four arrow keysChanging the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeResetting the picture mode Fine-tuning the picture qualityAdjusting Brightness Adjusting ContrastAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Flesh ToneSetting a preferred color temperature Setting Black LevelTo set a preferred color temperature Advanced picture quality controlsColor Management Selecting a Gamma settingAdjusting Brilliant Color To leave and save the settings, press MENU/EXIT Setting Film ModeSetting 3D Comb Filter Adjusting the sound level Adjusting the soundSwitching the left/right audio channels Turning off the Power On/Off Ring ToneAbout the aspect ratio Selecting the aspect ratioMagnifying and searching for details Using the test patternFreezing the image Operating in a high altitude environment To activate High Altitude ModeDisplaying more than one image source simultaneously To display the PIP window Using the remote controlUsing the OSD menu Using the 3D menus Watching 3D contentConnecting 3D video devices To lock the keys Personalizing the projector menu displayLocking control keys Turning the projector off On-Screen Display OSD menus Audio SetupOn-Screen Display OSD structure Main menu Sub-menu OptionsDisplay System Setup Auto OffInformation SetupAdvanced Function Description Picture -- Basic menuAudio Setup menu Display menu Advanced Setup menu System Setup menuPassword High Altitude ModeReset All Settings Test PatternInformation menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projectorExtending lamp life Lamp informationGetting to know the lamp hour Status Timing of replacing the lampReplacing the lamp Do not turn on the power with lamp cover removed Use the handle to slowly pull lamp housing out ProjectorConnect the power and restart the projector Resetting the lamp timerLamp Status & Description IndicatorsPower Temp Lamp Status & Description Problem Cause Remedy TroubleshootingYour Blu-ray Disc is not in 3D FormatSpecifications Ceiling mount installation DimensionsSupported timing for PC input Timing chartResolution Mode Refresh rate Freq. KHz Clock MHz 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input 1400 x SXGA+60 59.978 65.317 121.750 Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHzSupported timing for Video and S-Video inputs Resolution Mode Refresh rate Hz Freq. KHz Clock MHzVideo Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHz Copyright WarrantyDisclaimer Patents
Related manuals
Manual 72 pages 53.99 Kb