BenQ W1500 user manual Resetting the lamp timer, Connect the power and restart the projector

Page 56

11. Replace the lamp cover on the projector.

2

12. Tighten the screw that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

13. Connect the power and restart the projector.

Resetting the lamp timer

1

Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.

14.After the start-up logo, press MENU/EXIT and then press / until the Advanced Setup menu is highlighted.

15.Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page displays.

16.Highlight Reset Lamp Timer and press MODE/ENTER. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp time will be reset to "0".

56 Important safety instructions

Page 55 Page 57
Image 56
Page 55 Page 57
Contents W1500 Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewCeiling mounting the projector Replacing the remote control batteriesRemote control effective range Important safety instructions Projector features Projector exterior view Front and upper side view Rear and lower side viewRS-232 control port Audio L/R input jacksControls and functions Control panelRemote control Choosing a location FrontFront Ceiling RearObtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Important safety instructions Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen Floor Installation Ceiling InstallationScreen aspect ratio is 43 and the projected picture is Lowest HighestShifting the projection lens vertically To use the lens shift leverPreparations Terminal appearance ReferenceName ComponentConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on PreparationsSelecting an input source Sharpen the picture by rotating the focus ringUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password As the picture indicates, the four arrow keysEntering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 modeFine-tuning the picture quality Resetting the picture modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Flesh ToneSetting Black Level Setting a preferred color temperatureTo set a preferred color temperature Advanced picture quality controlsColor Management Selecting a Gamma settingAdjusting Brilliant Color To leave and save the settings, press MENU/EXIT Setting Film ModeSetting 3D Comb Filter Adjusting the sound Adjusting the sound levelSwitching the left/right audio channels Turning off the Power On/Off Ring ToneSelecting the aspect ratio About the aspect ratioMagnifying and searching for details Using the test patternFreezing the image To activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP window Using the remote controlUsing the OSD menu Using the 3D menus Watching 3D contentConnecting 3D video devices To lock the keys Personalizing the projector menu displayLocking control keys Turning the projector off Audio Setup On-Screen Display OSD menusOn-Screen Display OSD structure Main menu Sub-menu OptionsSystem Setup Auto Off DisplayInformation SetupAdvanced Picture -- Basic menu Function DescriptionAudio Setup menu Display menu System Setup menu Advanced Setup menuHigh Altitude Mode PasswordReset All Settings Test PatternInformation menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorExtending lamp life Lamp informationGetting to know the lamp hour Status Timing of replacing the lampReplacing the lamp Use the handle to slowly pull lamp housing out Projector Do not turn on the power with lamp cover removedResetting the lamp timer Connect the power and restart the projectorLamp Status & Description IndicatorsPower Temp Lamp Status & Description Troubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications Dimensions Ceiling mount installationSupported timing for PC input Timing chartResolution Mode Refresh rate Freq. KHz Clock MHz 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHz 1400 x SXGA+60 59.978 65.317 121.750Supported timing for Video and S-Video inputs Resolution Mode Refresh rate Hz Freq. KHz Clock MHzVideo Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHz Warranty CopyrightDisclaimer Patents
Related manuals
Manual 72 pages 53.99 Kb
Top Page Image Contents