BenQ W1500 user manual Information menu

Page 51

Information menu

This menu shows you the current operating status of the projector.

Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on the screen.

Function

Description

Source

Shows the current signal source.

 

 

Preset Mode

Shows the selected mode in the Picture -- Basic > Preset Mode menu.

 

 

Resolution

Shows the native resolution of the input source.

 

 

Color System

Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.

 

 

Equivalent Lamp

Shows the total lamp time used.

Hour

 

 

 

3D Format

Shows the current 3D mode.

3D Format is only available when 3D Mode is enabled.

 

 

 

Firmware Version

Shows the firmware version of your projector.

 

 

Important safety instructions

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents W1500 Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contentsReplacing the remote control batteries Remote control effective rangeCeiling mounting the projector Important safety instructions Projector features Audio L/R input jacks Projector exterior viewFront and upper side view Rear and lower side view RS-232 control portControl panel Controls and functionsRemote control Rear Choosing a locationFront Front CeilingDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeImportant safety instructions Installation for a 169 ratio screen Projection dimensionsLowest Highest Installation for a 43 ratio screenFloor Installation Ceiling Installation Screen aspect ratio is 43 and the projected picture isTo use the lens shift lever Shifting the projection lens verticallyComponent PreparationsTerminal appearance Reference NameConnecting Hdmi devices Connecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Turning the projector onSharpen the picture by rotating the focus ring Selecting an input sourceSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup menuAs the picture indicates, the four arrow keys Utilizing the password functionSetting a password If you forget the passwordWrite down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Setting the User 1/User 2/User 3 mode Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeAdjusting Contrast Fine-tuning the picture qualityResetting the picture mode Adjusting BrightnessAdjusting Flesh Tone Adjusting ColorAdjusting Tint Adjusting SharpnessAdvanced picture quality controls Setting Black LevelSetting a preferred color temperature To set a preferred color temperatureSelecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film Mode Setting 3D Comb FilterTo leave and save the settings, press MENU/EXIT Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Switching the left/right audio channelsAbout the aspect ratio Selecting the aspect ratioUsing the test pattern Freezing the imageMagnifying and searching for details Operating in a high altitude environment To activate High Altitude ModeTo display the PIP window Using the remote control Using the OSD menuDisplaying more than one image source simultaneously Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu display Locking control keysTo lock the keys Turning the projector off Main menu Sub-menu Options Audio SetupOn-Screen Display OSD menus On-Screen Display OSD structureDisplay System Setup Auto OffSetup AdvancedInformation Function Description Picture -- Basic menuAudio Setup menu Display menu Advanced Setup menu System Setup menuTest Pattern High Altitude ModePassword Reset All SettingsInformation menu Storing the projector Cleaning the lensCleaning the projector case Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Replacing the lampStatus Do not turn on the power with lamp cover removed Use the handle to slowly pull lamp housing out ProjectorConnect the power and restart the projector Resetting the lamp timerIndicators Power Temp Lamp Status & DescriptionLamp Status & Description Format TroubleshootingProblem Cause Remedy Your Blu-ray Disc is not in 3DSpecifications Ceiling mount installation DimensionsTiming chart Resolution Mode Refresh rate Freq. KHz Clock MHzSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input 1400 x SXGA+60 59.978 65.317 121.750 Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHzResolution Mode Refresh rate Hz Freq. KHz Clock MHz Video Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHzSupported timing for Video and S-Video inputs Patents WarrantyCopyright Disclaimer
Related manuals
Manual 72 pages 53.99 Kb
Top Page Image Contents