BenQ SP840 user manual Entering the password recall procedure, Changing the password

Page 28

Entering the password recall procedure

English

1.Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen.

2.Write down the number and turn off your projector.

3.Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

RECALL PASSWORD

Please write down the recall code, and contact BenQ

Customer Center.

Recall code:

12345678

MENU Exit

Changing the password

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings > Change password menu.

2.Press MODE/ENTER. The message 'INPUT CURRENT PASSWORD' displays.

3.Enter the old password.

If the password is correct, another message 'INPUT NEW PASSWORD' displays.

If the password is incorrect, the password error message displays lasting for three seconds, and the message 'INPUT CURRENT PASSWORD' displays for your retry. You can press MENU/EXIT to cancel the change or try another password.

4.Enter a new password.

The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __

Keep this manual in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new

password next time the projector is started.

Password Changed

7.To leave the OSD menu, press MENU/EXIT.

Disabling the password function

To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Power on Lock menu after opening the OSD menu system. Select Off by pressing / . The message 'INPUT PASSWORD' displays. Enter the current password.

i.If the password is correct, the OSD menu returns to the Security Settings page with Off shown in the row of Power on Lock. You will not have to enter the password next time you turn on the projector.

ii.If the password is incorrect, the password error message displays lasting for three seconds, and the message 'INPUT PASSWORD' displays for your retry. You can press MENU/EXIT to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

28 Operation

Image 28
Contents Welcome SP840 Digital ProjectorTable of contents Important safety instructions English Do not block the ventilation holes Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Rear/lower sideControls and functions ProjectorRemote control Operating the Laser pointer Remote control effective range Replacing the remote control batteryPositioning your projector Choosing a locationObtaining a preferred projected image size English SP840 projection dimensions Length AverageConnecting a computer or monitor Connecting a computerConnections To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitorWith a VGA cable With a VGA to DVI-A cable With a DVI input socketConnecting Video source devices Connecting AudioBest video quality Better video qualityConnecting Hdmi source devices To connect the projector to an Hdmi source deviceAV device Hdmi cableConnecting Component Video source devices To connect the projector to a Component Video source deviceTo connect the projector to an Audio source device Audio CableTo connect the projector to an S-Video source device Connecting S-Video source devicesVideo Cable AV device Audio Cable To connect the projector to a composite Video source device Connecting Composite Video source devicesAV device Video Cable Audio Cable Operation Starting up the projectorUsing the menus Using a security cable lockUse / to highlight the System Setup Basic menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password As pictured to the right, the four arrow keysChanging the password Entering the password recall procedureDisabling the password function Switching input signal Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using Auto KeystoneKeystone function Magnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Letter BoxSelecting a picture mode Setting the User 1/User 2/User 3 modeGo to the Picture Basic Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Adjusting Clarity Control Selecting a Color TemperatureSelecting a Color Temperature UserFine Tuning Selecting a Gamma SelectionSelecting a White Peaking Adjusting Brilliant Color3D Color Management Selecting Color Space Conversion Selecting a Video FormatRemote paging operations Selecting a Film ModeSelecting a 3D Comb Filter Locking control keys Setting the Sleep TimerHiding the image Freezing the image Adjusting the soundOperating in a high altitude environment Adjusting the sound level Adjusting the Treble levelAdjusting the Bass level Turning off the Power on/off Ring ToneControlling the projector through a Lan environment Configuring the Lan Control SettingsIf you are in a Dhcp environment Controlling the projector remotely through a web browser If you are in a non-DHCP environmentIiii Iiiv Personalizing the projector menu display Shutting down the projectorMenu operation Menu systemAdjustment Digital Zoom PC & Component YPbPr TuningMenu Settings Auto Power OffSecurity Settings SettingsReset All Settings Source Picture Mode Resolution Baud RatePicture Mode Description of each menuPicture Advanced Display menu System Setup Basic menu Hdmi Shows the current signal source Shows the selected mode in the Picture menuShows the native resolution of the input signal Displays the number of hours the lamp has been usedMaintenance Care of the projectorSetting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Loosen the screws that secure the lamp Setup Advanced Lamp Settings Tighten the screws that secure the lampIndicators OffRed Off GreenTroubleshooting Specifications Projector specificationsDimensions Timing chart Supported timing for Computer inputResolution Horizontal Vertical Pixel Mode Supported timing for Component-YPbPr inputSupported timing for Video and S-Video inputs Supported timing for Hdmi Hdcp inputSXGA60 Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directiveEnglish
Related manuals
Manual 71 pages 40.91 Kb