BenQ SP840 user manual Do not block the ventilation holes

Page 5

Safety Instructions (Continued)

12.Do not place this projector in any of the following environments.

-Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

-Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

-Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the projector's life span and darkening the image.

-Locations near fire alarms

-Locations with an ambient temperature above 35°C / 95°F

-Locations where the altitudes are higher than 3000 m (10000 feet).

3000 m

(10000 feet)

0 m

(0 feet)

13.Do not block the ventilation holes.

-Do not place this projector on a blanket, bedding or any other soft surface.

-Do not cover this projector with a cloth or any other item.

-Do not place inflammables near the projector.

If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.

14.Always place the projector on a level, horizontal surface during operation.

-Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.

15.Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

English

Important safety instructions

5

Image 5
Contents SP840 Digital Projector WelcomeTable of contents Important safety instructions English Do not block the ventilation holes Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewProjector Controls and functionsRemote control Operating the Laser pointer Replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorObtaining a preferred projected image size English Length Average SP840 projection dimensionsConnecting a computer Connecting a computer or monitorConnections To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting a monitorWith a VGA cable With a VGA to DVI-A cable With a DVI input socketConnecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an Hdmi source device Connecting Hdmi source devicesAV device Hdmi cableTo connect the projector to a Component Video source device Connecting Component Video source devicesTo connect the projector to an Audio source device Audio CableVideo Cable AV device Audio Cable Connecting S-Video source devicesTo connect the projector to an S-Video source device AV device Video Cable Audio Cable Connecting Composite Video source devicesTo connect the projector to a composite Video source device Starting up the projector OperationUsing a security cable lock Using the menusUse / to highlight the System Setup Basic menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password As pictured to the right, the four arrow keysDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityKeystone function Using Auto KeystoneCorrecting keystone Selecting the aspect ratio Magnifying and searching for detailsLetter Box About the aspect ratioSetting the User 1/User 2/User 3 mode Selecting a picture modeGo to the Picture Basic Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Selecting a Color Temperature Adjusting Clarity ControlSelecting a Color Temperature UserFine Tuning Selecting a Gamma Selection3D Color Management Adjusting Brilliant ColorSelecting a White Peaking Selecting a Video Format Selecting Color Space ConversionSelecting a 3D Comb Filter Selecting a Film ModeRemote paging operations Hiding the image Setting the Sleep TimerLocking control keys Operating in a high altitude environment Adjusting the soundFreezing the image Adjusting the Treble level Adjusting the sound levelAdjusting the Bass level Turning off the Power on/off Ring ToneIf you are in a Dhcp environment Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a non-DHCP environment Controlling the projector remotely through a web browserIiii Iiiv Shutting down the projector Personalizing the projector menu displayMenu system Menu operationYPbPr Tuning Adjustment Digital Zoom PC & ComponentMenu Settings Auto Power OffSettings Security SettingsReset All Settings Source Picture Mode Resolution Baud RateDescription of each menu Picture ModePicture Advanced Display menu System Setup Basic menu Hdmi Shows the selected mode in the Picture menu Shows the current signal sourceShows the native resolution of the input signal Displays the number of hours the lamp has been usedCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Loosen the screws that secure the lamp Tighten the screws that secure the lamp Setup Advanced Lamp SettingsOff IndicatorsRed Off GreenTroubleshooting Projector specifications SpecificationsDimensions Supported timing for Computer input Timing chartSupported timing for Component-YPbPr input Resolution Horizontal Vertical Pixel ModeSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputsSXGA60 Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directiveEnglish
Related manuals
Manual 71 pages 40.91 Kb