Bosch Appliances DVA-08K manual Drive Tray Specifications, Power Supply Specifications

Page 57

Drive Tray Specifications

RAID Subsystem DVA-08K Installation ManualAppendix: Technical Specifications en 57

7.2	Drive Tray Specifications

Specifications

Height

28mm

Width

110mm

Depth

218.92mm

Key Lock

Yes

7.3	Power Supply Specifications

		Specifications

	Nominal Power	350W

	DC Output	12.0V: 25A
		5.0V: 25A
		3.3V: 20A

	Input Frequency	47 to 63Hz

	AC Input	115VAC @ 6A or 240VAC @ 3A with PFC

	Power Factor Correction	Yes

	Hold-up Time	At least 16ms at 115/230VAC full load after a loss of
		AC input

	Over-temperature Protection	Auto shutdown when cooling is lost or elevated tem-
		perature is detected; over-voltage protection is also
		available.

	Cooling Fans	Two fans for each unit (inside PSU)

Bosch Security Systems

F.01U.027.797 V2 2008.08

Image 57

Contents DVA-08K SCSI Premium Series RAID Subsystem DVA-08KPage RAID Subsystem DVA-08K Installation Manual Table of ContentsTable of Contents en Bosch Security SystemsSubsystem Connection and Operation Precautions and Instructions Safety PrecautionsESD Precautions Warnings and CertificationsReorient or relocate the receiving antenna Introduction Product OverviewSCSI Host Ports Active Components Enclosure Chassis Physical Dimensions2.2.1 Chassis Overview2.2.5Rear Panel Overview 2.2.4Hard Drive Numbering2.2.6Backplane Board Subsystem Components 2.3.1LCD Panel 2.3.3 2.3.2Drive TraysThe RAID Controller Module Controller Module InterfacesDIMM Module 2.3.4Battery Backup Unit2.3.5 Power Supply Units2.3.6 Cooling Fan ModulesIntelligent Dual Speed Operation Advanced Fault-Preventative OperationAudible Alarms LED IndicatorsSubsystem Monitoring 2.4.12.5.1 Hot-Swappable ComponentsHot-Swap Capabilities 2.5.2Installation Prerequisites Hardware InstallationStatic-Free Installation Precautions and InstructionsBBU Warnings and Precautions 3.2.1Install or replace the BBU module only with a BBU module supplied by your subsystem vendor. Use of battery cells provided by another source will void our warranty Installation Procedure Flowchart General Installation ProcedureSection 5.4 Power On Installation Procedure3.5Rackmounting Considerations for Installation Site and Chassis3.5.1 3.5.23.6Drive Tray Installation 6. Once all drive trays are installed, the RAID subsystem will poll the drive channels and rec- ognize the drives and scan them in automatically Subsystem Monitoring Overview Subsystem Monitoring4.2.1 Status-indicating LEDsBrief Overview of the LEDs Component4.2.2Drive Tray LEDs Power Status4.2.3 Controller Module LEDsEthernet Port LEDs 4.2.4Name Link Status4.2.6 4.2.5BBU Module LEDPSU LED 4.2.7LCD Keypad PanelPOWER 4.2.8Cooling Fan Module LEDBUSY Default Threshold Values Audible Alarm4.3.1 Upper Threshold4.4I2C Monitoring 4.3.2Failed Devices Subsystem Connection and Operation Basic Configuration Rules5.2.1 SCSI Connection OverviewSCSI Cables 5.2.2SCSI Termination 5.2.3Host Connection Topology Default Channel SettingsModel Host ChannelsPower On Checklist Power OnPower On Sequence Power On ProcedurePower On Status Check 5.4.45.4.5LCD Screen 40 en Subsystem Connection and Operation Power Off Procedure General Notes on Component Replacement Subsystem Maintenance3. BBU module - Section 6.4 Replacing a Faulty BBU OverviewReplacing Controller Module Components Notes on Controller Module Maintenance6.2.1Overview 6.2.2Replacing the Controller Module 6.2.4DIMM Module Installation Memory Module Installation OverviewReplacing or Upgrading Memory Modules 6.3.13. Gently retrieve the DIMM module out of the DIMM socket. See Figure Notes on PSU Module Maintenance Replacing a Faulty BBUReplacing a Failed PSU Module 6.5.1The screw is located below the extraction lever, beside the LED indicator, and can be hid- den from sight 7. Insert the new PSU module into the subsystem Once the previously removed cooling module has been installed, insert the new PSU module into the subsystem. Make sure the extraction lever is in its downright position so that the saddle notches on the lower edges of the handle can lock on to the edge metal brackets along the chassis inner walls. Push the PSU into the slot and pull the handle upwards to secure the module Replacing a Failed Cooling Fan Module Notes on Cooling Fan Module Maintenance6.6.1 6.6.2Replacing a Cooling Fan ModuleNotes on Hard Drive Maintenance Drive Tray Maintenance6.7.1 6.7.2Replacing a Failed Hard DriveDrive type The subsystem can use either SATA-II or SATA-I hard drives Fig. 6.10 Installing a SATA Hard Drive Environmental Specifications Appendix Technical SpecificationsPower Requirements DimensionsWarning Alarms Safety RequirementsShock VibrationConfiguration Controller SpecificationsSpecifications 7.1.1Power Supply Specifications Drive Tray SpecificationsRAID Management Cooling Module SpecificationsFault Tolerance Management Spare Parts List Appendix Spare Parts and AccessoriesSpare Parts 8.1.1Accessories and Optional Items Appendix Pinouts SCSI Port VHDCI Connector PinoutsCN1 Pin Number COM1 Cable DB9 and Audio Jack PinoutsPin Name CN2 Pin NumberMain Power Null ModemEthernet Port Pinouts 10 Index terminal emulation program 17 terminal management 14 threshold values warning alarmsunder charge ventilation clearancePage Robert-Koch-Straße D-85521 Ottobrunn Bosch Security SystemsGermany Telefon