Bosch Appliances DVA-08K manual COM1 Cable DB9 and Audio Jack Pinouts, CN1 Pin Number, Pin Name

Page 63

COM1 Cable: DB9 and Audio Jack Pinouts

RAID Subsystem DVA-08K Installation ManualAppendix: Pinouts en 63

	Pin		Name	Pin	Name

	32		SD9+	66	SD9-

	33		SD10+	67	SD10-

	34		SD11+	68	SD11-

	Table 9.1	VHDCI Connector Pinouts (Cont.)
9.2	COM1 Cable: DB9 and Audio Jack Pinouts

i

Fig. 9.1 Serial Port Cable CN1 and CN2 Connectors

CN1 Pin Number	Pin Name

1	Ground

2	TXD

3	RXD

CN2 Pin Number	Pin Name

1	NC

2	RXD

3	TXD

4	DTR

5	GND

6	DSR

7	RTS

8	CTS

9	NC

Pin 4 and Pin 6 are shorted
Pin 7 and Pin 8 are shorted

Table 9.2 COM 1 Cable, RS-232C (Audio Jack) Pin Out Definitions
NOTICE!

A null modem is used for wire-swap and is necessary for connecting in between COM1CN2 and a PC serial port.

Bosch Security Systems

F.01U.027.797 V2 2008.08

Image 63

Contents DVA-08K SCSI Premium Series RAID Subsystem DVA-08KPage Bosch Security Systems Table of ContentsRAID Subsystem DVA-08K Installation Manual Table of Contents enSubsystem Connection and Operation Warnings and Certifications Safety PrecautionsPrecautions and Instructions ESD PrecautionsReorient or relocate the receiving antenna Introduction Product OverviewSCSI Host Ports Active Components Chassis Overview Physical DimensionsEnclosure Chassis 2.2.12.2.5Rear Panel Overview 2.2.4Hard Drive Numbering2.2.6Backplane Board Subsystem Components 2.3.1LCD Panel Controller Module Interfaces 2.3.2Drive Trays2.3.3 The RAID Controller ModuleDIMM Module 2.3.4Battery Backup UnitCooling Fan Modules Power Supply Units2.3.5 2.3.6Intelligent Dual Speed Operation Advanced Fault-Preventative Operation2.4.1 LED IndicatorsAudible Alarms Subsystem Monitoring2.5.2 Hot-Swappable Components2.5.1 Hot-Swap CapabilitiesInstallation Prerequisites Hardware Installation3.2.1 Precautions and InstructionsStatic-Free Installation BBU Warnings and PrecautionsInstall or replace the BBU module only with a BBU module supplied by your subsystem vendor. Use of battery cells provided by another source will void our warranty Installation Procedure General Installation ProcedureInstallation Procedure Flowchart Section 5.4 Power On3.5.2 Considerations for Installation Site and Chassis3.5Rackmounting 3.5.13.6Drive Tray Installation 6. Once all drive trays are installed, the RAID subsystem will poll the drive channels and rec- ognize the drives and scan them in automatically Subsystem Monitoring Overview Subsystem MonitoringComponent Status-indicating LEDs4.2.1 Brief Overview of the LEDsController Module LEDs Power Status4.2.2Drive Tray LEDs 4.2.3Link Status 4.2.4Ethernet Port LEDs Name4.2.7LCD Keypad Panel 4.2.5BBU Module LED4.2.6 PSU LEDPOWER 4.2.8Cooling Fan Module LEDBUSY Upper Threshold Audible AlarmDefault Threshold Values 4.3.14.4I2C Monitoring 4.3.2Failed Devices Subsystem Connection and Operation Basic Configuration Rules5.2.2 SCSI Connection Overview5.2.1 SCSI CablesSCSI Termination 5.2.3Host Channels Default Channel SettingsHost Connection Topology ModelPower On Procedure Power OnPower On Checklist Power On SequencePower On Status Check 5.4.45.4.5LCD Screen 40 en Subsystem Connection and Operation Power Off Procedure Overview Subsystem MaintenanceGeneral Notes on Component Replacement 3. BBU module - Section 6.4 Replacing a Faulty BBU6.2.2 Notes on Controller Module MaintenanceReplacing Controller Module Components 6.2.1OverviewReplacing the Controller Module 6.2.46.3.1 Memory Module Installation OverviewDIMM Module Installation Replacing or Upgrading Memory Modules3. Gently retrieve the DIMM module out of the DIMM socket. See Figure 6.5.1 Replacing a Faulty BBUNotes on PSU Module Maintenance Replacing a Failed PSU ModuleThe screw is located below the extraction lever, beside the LED indicator, and can be hid- den from sight 7. Insert the new PSU module into the subsystem Once the previously removed cooling module has been installed, insert the new PSU module into the subsystem. Make sure the extraction lever is in its downright position so that the saddle notches on the lower edges of the handle can lock on to the edge metal brackets along the chassis inner walls. Push the PSU into the slot and pull the handle upwards to secure the module 6.6.2Replacing a Cooling Fan Module Notes on Cooling Fan Module MaintenanceReplacing a Failed Cooling Fan Module 6.6.16.7.2Replacing a Failed Hard Drive Drive Tray MaintenanceNotes on Hard Drive Maintenance 6.7.1Drive type The subsystem can use either SATA-II or SATA-I hard drives Fig. 6.10 Installing a SATA Hard Drive Dimensions Appendix Technical SpecificationsEnvironmental Specifications Power RequirementsVibration Safety RequirementsWarning Alarms Shock7.1.1 Controller SpecificationsConfiguration SpecificationsPower Supply Specifications Drive Tray SpecificationsRAID Management Cooling Module SpecificationsFault Tolerance Management 8.1.1 Appendix Spare Parts and AccessoriesSpare Parts List Spare PartsAccessories and Optional Items Appendix Pinouts SCSI Port VHDCI Connector PinoutsCN2 Pin Number COM1 Cable DB9 and Audio Jack PinoutsCN1 Pin Number Pin NameMain Power Null ModemEthernet Port Pinouts 10 Index ventilation clearance warning alarmsterminal emulation program 17 terminal management 14 threshold values under chargePage Telefon Bosch Security SystemsRobert-Koch-Straße D-85521 Ottobrunn Germany