3M S40, X40 manual Phenomena That May Easily Be Mistaken for Machine Defects, Phenomenon

Page 37

Phenomena That May Easily Be Mistaken for Machine Defects

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.

Phenomenon

Cases not involving a machine defect

Items to be confirmed

Reference

Page(s)

 

 

 

 

 

 

 

 

The main power source is not ON.

Turn on the main power.

3, 14

 

 

 

 

The electrical power cord is not plugged in.

Correctly connect the power cord.

 

 

 

 

 

 

Power does not

 

Be sure to press the “O” (power OFF) side

 

come ON

The main power source has been

of the main power switch, and leave this OFF

14

 

interrupted during operation, such as by

for approximately 20 minutes. After the unit

 

a power outage (blackout), etc.

has sufficiently cooled down, turn ON the

 

 

 

power source.

 

 

 

 

 

No sound or

The input changeover settings

Select the input signal, and

15

are mismatched.

correct the settings.

pictures are

 

 

 

 

 

 

 

outputted

No signal is being inputted.

Correctly connect the connection cord.

10, 11

 

 

 

 

 

The electrical wiring to this unit

Correctly connect the connection cord.

10, 11

 

is not correctly connected.

Pictures are

 

 

 

 

 

The volume setting has been set at (or

 

17

displayed, but no

Adjust the VOLUME setting to a higher level.

adjusted to) an extremely low level.

sounds are heard

 

 

 

 

 

The MUTE mode is the current setting.

Press the MUTE button to release

17

 

 

 

(change) the MUTE mode setting.

 

Sounds are

The electrical wiring to this unit

Correctly connect the connection cord.

10, 11

heard, but no

is not correctly connected.

 

 

pictures are

 

 

 

The brightness setting has been set at

Adjust the BRIGHT setting to a

24

displayed

(or adjusted to) an extremely low level.

brighter level.

 

 

 

 

 

 

Colors have a faded-

 

Perform picture adjustments by changing the

25

out appearance

Color depth setting or color tone setting

COLOR BAL R, the COLOR BAL B, and/or the

Color tone is poor

 

TINT settings, etc.

 

 

 

 

 

 

The brightness setting and/or contrast

Perform picture adjustments by changing the

24

 

setting has not been properly adjusted.

BRIGHT and/or CONTRAST settings, etc.

 

Pictures appear

The WHISPER mode is the current

Change (by releasing) from the

28

dark

setting.

WHISPER mode.

 

 

Lamp is approaching the end of its

Exchange the old lamp with a new

24, 25

 

product lifetime.

lamp.

 

 

 

 

 

Pictures appear

Either the FOCUS setting or the H

Adjust the FOCUS and H PHASE settings.

15, 25

blurry

PHASE is not properly adjusted.

 

 

 

 

 

 

NOTE

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

36

Page 36 Page 38
Image 37
Page 36 Page 38
Contents S40/X40 Multimedia Projector S40/X40 Multimedia Projector Operators Guide ContentsPower cord Projector FeaturesCable Connect your devices to the projector Projector Part NamesTerminal Panel Adjusting the Projectors Elevator Foot Setting UP the ProjectorIf 43 aspect ratio Adjusting the Screen Size and Projection DistanceConnecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerPutting batteries into the remote control unit Using the Remote ControlRemove the battery cover Close the battery coverOperating the remote control Precautions Turning on the PowerMake sure that the power cord is firmly Turn on the projectors powerUse the zoom ring to adjust Selecting an Input SignalScreen size Use the focus ring to focus the pictureAgainremote control or control panel Turning OFF the PowerPress the STANDBY/ON button of remote Controrol or the on/off button of control panelPress the Volume button Adjusting the VolumePress Buttons to adjust Volume Temporarily Muting the SoundUse Buttons to adjust Position Adjusting the PositionPress the Position button Automatic Adjustment for RGB Input Using the Automatic Adjustment FeatureAutomatic Adjustment for Video Input Press the Auto buttonPress the Keystone button Correcting Keystone DistortionsUse the , buttons to correct DistortionFreezing the Screen Using the Magnify FeatureSelecting the Aspect Ratio Signal SearchingTemporarily Blanking the Screen Select a menu using Buttons Then press Or Enter button Using the Menu FunctionsSelect an item using Buttons, then press Or Enter button Press Buttons to adjust the levelMain Menu Multifunctional SettingsMain Menu PICTURE-2 Menu PICTURE-1 MenuPICTURE-1 Menu PICTURE-2 MenuInput Menu Input MenuAuto VideoScreen Menu Screen MenuBlank Start UPOption Menu Option MenuAuto OFF WhisperLamp High Voltage High Temperature High PressureLeast 45 minutes, and prepare a new Replacing the lampCaring for the air filter AIR FilterAir Filter Replacing the air filter Other Care Caring for the cabinet and remote control transmitterCaring for the inside of the projector Caring for the lensRelated Messages Power Lamp Temp Description Regarding the Indicator LampsPhenomenon Phenomena That May Easily Be Mistaken for Machine DefectsItems to be confirmed Dimension Diagram SpecificationsSpecification Part Number How to OrderDN00571 S30/X40OGENG
Top Page Image Contents