Onkyo TX-NR3008 Firmware Update, Updating the Firmware via Network, Before you start

Page 112

Firmware Update

There are the following methods to update the firmware: via network and via USB storage. Please choose either one that suits your condition. Before you start, carefully read the update procedure. It will take about 60 minutes to update the firmware.

■Update via network

You need a wired Internet connection to update the firmware.

■Update via USB storage (➔ 113)

Please prepare a USB storage device such as a USB flash memory stick. You need at least 32 MB of avail- able space to update the firmware.

Note

•The storage media in the USB card reader may not work.

•If the storage device has been partitioned, each section will be treated as an independent device.

•If the USB mass storage device contains a lot of data, the AV receiver may take a while to read it.

•Operation with all USB mass storage devices including the abil- ity to power them is not guaranteed.

•Onkyo accepts no responsibility whatsoever for the loss or dam- age to data stored on a USB mass storage device when that device is used with the AV receiver. We recommend that you back up your important music files beforehand.

•If you connect a USB hard disk drive to the USB port, we rec- ommend that you use its AC adapter to power it.

•USB hubs and USB devices with hub functions are not sup- ported. Do not connect your USB mass storage device via a USB hub.

•USB memory devices with security functions are not supported.

•In no event shall Onkyo be liable to you or any third party for any damages, whatsoever, arising from your use of or inability to use the firmware, including but not limited to, loss of any equipment, media or data, or other special, incidental or consequential dam- ages, even if Onkyo has been advised of the possibility of such damages.

See the Onkyo web site for latest information.

Updating the Firmware via Network

The AV receiver allows you to update firmware using Net- work connection on rear panel.

*In this procedure, on-screen display may vary depending on the model.

Note

•Make sure your AV receiver and TV are turned on and Ethernet cable is connected to rear panel of the AV receiver.

•Never unplug or turn off the AV receiver during updating pro- cess.

•Never plug or unplug an HDMI cable and Ethernet cable during updating process.

•Never unplug the power cord during updating process.

•It will take about 60 minutes to update the firmware.

•The AV receiver will retain all your settings after update is fin- ished.

Before you start

•Check “HDMI Control(RIHD)” setting (➔ 65). The update may not be successful if this setting is on.

•Turn off the controller device connected via RS232C and via Ethernet network.

•Turn off Powered Zone 2 and Powered Zone 3.

•Stop playback of content from Internet Radio, iPod, USB or Servers, etc.

■How to turn off RIHD

 

 

1

In the Main menu select “Hardware Setup”.

2

Select “HDMI”.

3

Set “HDMI Control(RIHD)” to “Off”.

Update procedure

 

 

1

Press RECEIVER followed by SETUP on the

 

remote controller.

 

Main menu will be displayed on TV screen. Proce-

 

dures thereafter can also be performed on the AV

 

receiver by using its SETUP, arrow, and ENTER

 

buttons.

 

 

2

Go to “Hardware Setup” menu.

3

Go to “Firmware Update” menu.

 

Note that the Firmware Update option will be grayed

 

out about 50 seconds after AV receiver is turned on.

 

Please wait.

 

 

4

Select “Via NET” and press ENTER.

5

Select “Update” and press ENTER.

 

Updating will begin.

 

As the updating progresses, the TV screen may dis-

 

appear depending on the program updated. In this

 

case, you can see the update progress on the front

 

display of the AV receiver. The TV screen will reap-

 

pear when you finish the update and turn on the AV

 

receiver.

 

 

6

Message “Complete!” appears on the front dis-

 

play of the AV receiver, indicating that the update

 

has been completed.

 

 

7

Using ON/STANDBY on the front panel, turn off

 

and on the AV receiver.

Do not use ON or STANDBY on the remote control- ler.

Congratulations!! Now you have the latest firmware on your Onkyo AV receiver.

En

112

Page 111 Page 113
Image 112
Page 111 Page 113
Contents TX-NR5008 TX-NR3008 Always consider the environmental issues and follow 10 cm 4 at the rear. The rear edge of the shelf orBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Supplied Accessories Using the Remote ControllerInstalling the Batteries Aiming the Remote ControllerContents Features AmplifierProcessing MiscellaneousV.Color is a trademark of Sony Corporation THX Ultra2 PlusMusic Optimizer is a trademark of Onkyo Corporation Pure Audio button Hdmi Thru indicator Front & Rear PanelsFront Panel ON/STANDBY buttonReturn button Setup MIC jack DisplayPhones jack Zone 2, Zone 3 and OFF buttons AUX Input jacks HDMI, VIDEO, Audio L/R and Digital 21Ethernet port UREMOTE Control jack Rear PanelZone 2 and Zone 3 12V Trigger OUT jacks Front L/R, CENTER, Surr L/RRemote Controller Controlling the AV ReceiverAbout Home Theater Enjoying Home TheaterConnecting the AV Receiver Connecting Your SpeakersAbout Speakers a and Speakers B Speakers a 7.2-channel playback Speakers B Stereo playbackSpeaker Configuration Speaker Connection PrecautionsRead the following before connecting your speakers Attaching the Speaker Cable LabelsConnecting the Speaker Cables Screw-type speaker terminals Strip 1/2 to 5/8 12 to 15 mmChannel Playback with Speakers a To 5/812 to 15 mmChannel Playback with Speakers a or Speakers B Center Speaker BConnecting the Powered Subwoofers Using Dipole SpeakersBi-amping the Front Speakers a Speakers TypeFront B setting to Bi-Amp to enable biamping Bridging the Front Speakers aBi-amping the Front Speakers B Front L/R and Surr BACK/ZONE 3 L/R terminalsBridging the Front Speakers B Connecting a Power AmplifierSpecify None for the channel that you don’t want to output About AV Connections Connected image with AV componentsAV Cables and Jacks Hdmi cableJack Signal Components Assignable Connecting Your Components with HdmiAudio return channel ARC function Connecting Your Components Front RearConnecting Onkyo uComponents How to record the videoAuto Power On Remote ControlConnecting Antenna Connecting the Power CordNorth American European and Asian Models AC InletWhich Connections Should I Use? Video Connection FormatsMonitor Out setting set to Analog For details, refer to Video Resolution ChartDepends on the Audio TV Out setting Audio Connection FormatsStandby indicator Turning On/Off the AV ReceiverTurning On Turning OffSelecting the Language Used for the Onscreen Setup Menus Setting the Display BrightnessBasic Operations Playing the Connected ComponentUsing the Sleep Timer Speakers a or Speakers B ConfigurationMuting the AV Receiver Selecting Speaker LayoutUsing the Home Menu Using Headphones Using Activities to Start Easy MacrosStarting Components Using Activities Changing the Input DisplayAudyssey MultEQ XT32 Room Correction and Speaker Setup Restoring DefaultUsing Audyssey MultEQ XT32 Turning Off the ComponentsEnter Changing the Speaker Settings Manually Error MessagesUsing a Powered Subwoofer Using the Tuner Tuning into Radio StationsListening to the Radio Listening to the RadioPresetting FM/AM Stations Using RDS excluding North American modelsListening to Traffic News TP Finding Stations by Type PTYRDS program types PTY Connecting a Recording Component RecordingRecording Separate AV Sources AV RecordingListening Mode Buttons Using the Listening ModesSelecting Listening Modes About Listening Modes Explanatory NotesInput Source Speaker LayoutListening Modes Resolution Audio Description Input Speaker Source Layout DTS-HD HighDTS-HD Master AudioListening Mode Description Input Speaker Source Layout Modes can be used Neural DigitalMusic *6 Sources such as MP3s and Internet streamsOnkyo-Original DSP Listening Modes Advanced Setup On-screen Setup MenusCommon Procedures in Setup Menu MenuInput/Output Assign Monitor OutOUT Main OUT SUBHdmi Input ResolutionBD/DVD, VCR/DVR, CBL/SAT, GAME, PC, Tape TV/CD, PHONO, Port ` in 1, in 2, Component Video InputInput to Port selector Speaker Setup Speaker SettingsDigital Audio Input Analog Audio InputPowered Zone 2, Powered Zone Speaker ImpedanceSpeakers TypeFront a Speakers TypeFront BSpeaker Distance Equalizer Settings Level CalibrationSubwoofer 1*1, Subwoofer 2*1*2 EqualizerAudio Adjust THX Audio SetupMultiplex/Mono BGCDolby Audyssey DSX Theater-DimensionalLFE Level Source Setup DirectAudyssey DSDDynamic Volume Sync IntelliVolumeName Edit Picture Adjust Resolution*2*4 Mosquito NR*2*3*4*6Random NR*2*3*4*6 Block NR*2*3*4*6Listening Mode Preset DTS/DTS-ES/DTS-HDOSD Setup Volume SetupMiscellaneous Hardware Setup Sirius Settings North American modelsRemote ID Multi ZonePower Control Hdmi ControlRIHDAudio Return Channel TV ControlLock Setup Using the Audio SettingsAudyssey Settings Dolby VolumeSpeaker Levels Late NightRe-EQ Screen Centered DialogAudio Selector Setting the Incoming Digital Signal Fixed Mode Fixed Mode` PCM ` DTSAbout NET Connecting the AV ReceiverNetwork Requirements Click on the Preset Internet Radio tab Listening to Internet RadioListening to vTuner Internet Radio Listening to Other Internet RadioRegistering Presets*1 Station and Song PresetsPlaying Music Files on a Server Items on the Internet Radio Top MenuWindows Media Player 11 Setup Supported Audio File Formats WMAWAV AACWindows Media Player 12 Setup Remote Playback from Media Server/ Personal ComputerServer Requirements About DlnaNetwork Settings Using Remote PlaybackDhcp List of the device’s contents appears About USBUSB Mass Storage Device Requirements Playing Music Files on a USB DeviceFolder1 02SongTrack2 Artist Album 011234 Connecting Zone Connecting Your Zone 2 Speakers Directly to the AV receiverConnecting Your Zone 2 Speakers to an Amp in Zone Multi ZoneZone 2 Video Output Connecting Your Zone 3 Speakers Directly to the AV receiverZone 2 12V Trigger Setting the Powered Zone 2/3 Connecting Your Zone 3 Speakers to an Amp in ZoneZone 3 12V Trigger Front WIDE/ZONE 2 L/R or SurrUsing Zone 2/3 Setting the Multi ZoneControlling Zone 2/3 from the AV receiver Controlling Zone 2/3 with the Remote Controller Adjusting the Volume for ZonesAdjusting the Tone and Balance of Zones Muting ZonesUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with Zone 2/3Using a Multiroom Kit with Other Components Connecting the iPod Directly to the USB Port Standard Mode controlExtended Mode control Controlling iPodConnecting an Onkyo Dock TX-NR5008 TX-NR3008Models sold are different depending on the region Onkyo Dock CableUsing the Onkyo Dock UP-A1 DockControlling Your iPod RI DockWithout the RI Control With the RI ControlAvailable buttons Onkyo Dock Buttons UP-A1 DockUDock E/rENTER PLAYLISTe/rLooking up for Remote Control Code Preprogrammed Remote Control CodesControlling Other Components Use q/wto select Search by model number Via network, and then press EnterModel number input panel appears Or if you are not sure about the exact modelEntering Remote Control Codes Remote Control Codes for Onkyo Components Connected via uRemote Mode BD/DVD TapeResetting Remote Mode Buttons Resetting the Remote ControllerYou can reset the remote controller to its default settings Controlling Other ComponentsComponents Buttons Cassettetape deckTV VOL q/w CH + Disc +Activities Setup Learning Commands Remote Mode button flashes twiceFollowing buttons cannot learn new commands Remote MODE, ALL OFF, MY MOVIE, MY TV, MY Music and ModeUsing Normal Macros Deleting Learning CommandsMaking Macros Running MacrosTroubleshooting Standby indicator flashes redThere’s no sound, or it’s very quiet Can’t turn on the AV receiverThere’s no sound with a certain signal format Can’t select the Pure Audio listening modeAbout DTS signals Only the center speaker produces soundRemote controller doesn’t work Beginning of audio received by an Hdmi in can’t be heardThere’s no picture There’s no picture from a source connected to an HdmiCan’t learn commands from another remote controller Can’t access the server or Internet radioCan’t access the music files on a USB device Can’t control other componentsStand-by power consumption Sound changes when I connect my headphonesSpeaker distance cannot be set as required Display doesn’t workImportant Note Regarding Video Playback Nent Video Monitor OUTSpecifications TX-NR5008 Amplifier Section Tuner SectionGeneral Video SectionAudio Outputs Audio InputsOthers Specifications TX-NR3008 107108 Supported Audio Formats About HdmiAbout Copyright Protection About p-compatible components Using an RIHD-compatible TV, Player, or RecorderOperations that can be performed with p connection How to connect and setup Confirm the connecting and settingConfirm the settings Operate with the remote controllerFirmware Update Update procedureUpdating the Firmware via Network Before you startErrors during update via Network TroubleshootingUpdating the Firmware via USB Errors during update via USB Video Resolution Chart OutputOnkyo Europe Electronics GmbH Onkyo Europe Electronics GmbH UK Branch
Related manuals
Manual 2 pages 42.89 Kb

TX-NR3008 specifications

The Onkyo TX-NR3008 is a high-performance A/V receiver that has garnered attention for its impressive array of features and advanced technologies. As part of Onkyo's acclaimed line of home theater receivers, the TX-NR3008 is designed to deliver an immersive audio and video experience, making it an ideal choice for audiophiles and home theater enthusiasts alike.

One of the standout features of the TX-NR3008 is its powerful amplifier section, capable of delivering 135 watts per channel (8 ohms) across all seven channels. This ensures rich, dynamic sound reproduction, whether you are watching your favorite movies or listening to music. The receiver also supports 9.2-channel surround sound, allowing users to add external amplifiers to create a more expansive soundstage.

In terms of audio processing, the TX-NR3008 incorporates advanced DTS-HD Master Audio and Dolby TrueHD formats, which provide lossless audio quality for a truly cinematic experience. Additionally, the receiver is equipped with Onkyo's proprietary AccuEQ room calibration technology, which analyzes the acoustics of your space and optimizes sound output accordingly. This ensures that every listener experiences superior sound quality, regardless of seating position.

The TX-NR3008 also offers an array of connectivity options. With six HDMI inputs, including support for 3D video and 4K resolution, users can easily connect various devices, such as Blu-ray players, gaming consoles, and streaming devices. The HDMI capabilities extend to audio return channel (ARC) functionality, making it convenient to connect with smart TVs. The receiver also provides legacy support with composite and component video inputs, as well as digital optical and coaxial audio inputs.

Another notable feature is its built-in internet streaming capabilities, allowing users to access popular music services like Pandora, Spotify, and SiriusXM right from the receiver. Its compatibility with Wi-Fi and wired Ethernet connections adds further versatility, enabling the TX-NR3008 to be incorporated into multi-room audio setups.

In summary, the Onkyo TX-NR3008 is a formidable A/V receiver that excels in delivering top-notch audio and video performance. Its robust amplification, advanced surround sound processing, extensive connectivity options, and streaming capabilities make it an exceptional choice for anyone looking to create an immersive home theater experience. With its blend of power, precision, and versatility, the TX-NR3008 remains a strong contender in the competitive market of high-end A/V receivers.
Top Page Image Contents