Onkyo TX-NR3008 instruction manual Listening Mode Preset, Dts/Dts-Es/Dts-Hd

■Blue Contrast*2*4

`–50 to 0 to +50

With this setting you can adjust blue contrast. “–50” is the least. “+50” is the greatest.

	Tip
*1	This procedure can also be performed on the remote controller
	by using the Home menu (➔ 30).
*2	Press CLR if you want to reset to the default value.

Note

•If you are using the analog RGB input, the following settings have no effect: “Film Mode”, “Edge Enhancement”, “Mos- quito NR”, “Random NR” and “Block NR”.

•“Picture Adjust” is not operable when the input selector is set to “NET/USB”.

*3 These settings have no effect in the case of HD input source (720p,1080i,1080p,1080p/24).

*4 When the “Picture Mode” setting is set to anything other than “Custom”, this setting cannot be used.

*5 Depending on the input and output resolutions, “Smart Zoom” may not be used.

*6 When the “Game Mode” setting is set to “On”, this setting cannot be selected.

*7 This setting have no effect in the case of downconversion.

Listening Mode Preset

You can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default lis- tening mode to be used with Dolby Digital input signals. You can select other listening modes during playback, but the mode specified here will be resumed once the AV receiver has been set to Standby.

Main menu	Listening Mode Preset
1 Use q/wto select the input source that you want to

set, and then press ENTER.

The following menu appears.

	5. Listening Mode Preset
1.	BD/DVD
2.	VCR/DVR
3.	CBL/SAT
4.	GAME
5.	PC
6.	AUX

For “TUNER” input selector only “Analog” will be available. For “NET/USB” input source only “Digi- tal” will be available.

Note

•If you connect an input component (such as UP-A1 series Dock that seated iPod) to the UNIVERSAL PORT jack, you can assign only listening modes for the analog sound to “PORT” selector.

2 Use q/wto select the signal format that you want to set, and then use e/rto select a listening mode.

	Only listening modes that can be used with each
	input signal format can be selected (➔ 40 to 45).
	The “Last Valid” option means that the listening
	mode selected last will be used.
	The “Straight Decode” option means that straight
En	decoding listening mode (Dolby Digital, DTS, etc.)
	is selected.

■Analog/PCM

With this setting, you can specify the listening mode to be used when an analog (CD, TV, LD, VHS, MD, turn- table, radio, cassette, cable, satellite, etc.) or PCM digi- tal (CD, DVD, etc.) audio signal is played.

■Mono/Multiplex Source

With this setting, you can specify the listening mode to be used when a mono digital audio signal is played (DVD, etc.).

■2ch Source

With this setting, the default listening mode for 2-chan- nel (2/0) stereo sources in a digital format, such as Dolby Digital or DTS.

■Dolby D/Dolby D Plus/TrueHD

With this setting, you can specify the listening mode to be used when a Dolby Digital or Dolby Digital Plus for- mat digital audio signal is played (DVD, etc.). Specifies the default listening mode for Dolby TrueHD sources, such as Blu-ray or HD DVD (input via HDMI).

■DTS/DTS-ES/DTS-HD

With this setting, you can specify the listening mode to be used when a DTS or DTS-HD High Resolution Audio format digital audio signal is played (DVD, LD, CD, etc.). Specifies the default listening mode for DTS- HD Master Audio sources, such as Blu-ray or HD DVD (input via HDMI).

■Other Multich Source

Specifies the default listening mode for multichannel PCM sources from HDMI IN such as DVD-Audio, and DSD multichannel sources such as Super Audio CD.

62