LG Electronics M2794A, M2394A owner manual Switch ON/OFF, Simple Text

Page 52

TELETEXT

This feature is not available in all countries.

Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, televi- sion programmes, share prices and many other topics.

The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.

SWITCH ON/OFF

Press the TEXT button to switch to teletext. The initial page or last page viewed appears on the screen.

Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.

Press the TEXT or RETURN button to switch off teletext. The previous mode reappears.

SIMPLE TEXT

A Page selection

1Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number.

2The PR D / E button can be used to select the preceding or following page.

A Programming a colour button in LIST mode

If the TV is in SIMPLE text,TOP text or FASTEXT mode, press the butto to switch to LIST mode.

Four teletext page umbers of your choice can be colour coded and easily selected by pressing the corresponding coloured button on the remote control handset.

1Press a coloured button.

2Using the NUMBER buttons,select the page you wish to programme.

3Press the OK button. The selected page is stored as the selected page umber, blinking once to confirm this.

From now on, you can select this page with the same coloured button.

4The three other coloured buttons are programmed in this way.

51

Image 52
Contents Page Preparation Front Panel ControlsBack Panel Information Video Input Connect S-Video out from an S-VIDEO deviceStand Installation Image shown may be somewhat different from your setDetaching Stand Wall Mount Horizontal Installation Desktop Pedestal InstallationPositioning Your Display LocationKensington Security System External Equipment Setup Antenna ConnectionWhen connecting with a component cable HD Receiver Setup480i/576iYes 480p/576pYes 720p/1080iYes 1080pYes When connecting with a Hdmi When connecting with a Hdmi to DVI cableHdmi jack on the set Press the Input button to select HDMI1 or HDMI2DVD Setup Component Input portsWhen connecting Hdmi cable VCR Setup When connecting with an antennaWhen connecting with a RCA cable When connecting with an S-Video cablePC Setup When connecting with a D-sub 15 pin cableWhen connecting with a DVI cable Back Cover for Wire Arrangement Hdmidtv supported mode RGB/DVIPCRemote Control KEY Functions Watching TV /PROGRAMME ControlInserting batteries into remote control Watching TV /PROGRAMME ControlTurning on the SET Volume AdjustmentProgramme Selection On Screen Menus Selection and Adjustment Setup Picture AudioAuto Programme Tuning PAL I/II U.K. / Ireland / Hong Kong / South AfricaTo Set Assigning a Station Name Fine TuningBooster Programme Edit Copying a programmeSelect a programme to be copied with the D / E / F / G ButtonSelect a desired programme with the F / G button or Number Favourite ProgrammeIt, i.e.‘05’ for Selecting the Programme List Watching PIP PICTURE-IN-PICTURE Picture Control Picture Size Aspect RatiocontrolZoom1 Zoom2Preset Picture Settings Picture Mode-PresetLevel, the softer the image Manual Picture AdjustmentTV/AV/Component/HDMI Auto Colour Tone ControlCool/Medium/Warm Colour Tone User Mode Picture Improvement Technology Manual SelectionAdvanced Gamma To set up for the best picture quality for viewing filmsAdvanced Blackdarkness Level Picture Reset Auto Configure RGB PC mode only Using OKRemocon or control keyAuto Config. OK Others ResolutionManual Config Selecting Resolution Initializing Reset to original factory settingsPreset Sound SETTINGS-SOUND Mode Sound Setting Adjustment -USER ModeTV Speakers ON/OFF Setup Auto Volume LevelerBalance Nicam Reception Stereo/Dual ReceptionSpeaker Sound Output Selection Clock Setup Auto ON/OFF Time SettingSleep Timer Setting Auto SHUT-OFF SettingON-SCREEN Menu Language Selection Press the OK buttonOption Setting KEY LockIf you set ON, you enable the response time control function Press the G button and then D / E button to select RTCPower Indicator Factory ResetSwitch ON/OFF Simple TextTOP Text FastextSpecial Teletext Functions Select the each indexTroubleshooting Remote control Doesn’t work Power is suddenly Turned offAppendix From the web site User’s guideProduct is turned off Is the screen position Wrong?Maintenance Cleaning the ScreenCleaning the Cabinet Extended AbsenceProduct Specifications M2394AM2794A Remote Control IR Codes How to ConnectIR Codes Code Function Type of Connector D-Sub 9-Pin Male RS-232C SetupExternal Control Through RS-232C Set ID RS-232C ConfigurationsCommunication Parameters Command Reference List Transmission / Receiving ProtocolTransmission ka Set ID DataCr Transmission kk Set ID DataCr LSB