LG Electronics M2394A, M2794A owner manual External Equipment Setup, Antenna Connection

Page 9

EXTERNAL EQUIPMENT SETUP

■To prevent equipment damage, never plug in any power cords until you have finished connecting all equipment.

ANTENNA CONNECTION

■For optimum picture quality, adjust antenna direction.

■An antenna cable and converter are not supplied.

Wall

Antenna

Socket

Outdoor

Antenna

(VHF, UHF)

Antenna

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

UHF

Signal

Amplifier

VHF

ANTENNA/

CABLE IN

ANTENNA/

CABLE IN

■In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.

■If signal needs to be split for two sets, use an antenna signal splitter for connection.

8

Image 9

Contents Page Front Panel Controls PreparationVideo Input Connect S-Video out from an S-VIDEO device Back Panel InformationImage shown may be somewhat different from your set Stand InstallationDetaching Stand Desktop Pedestal Installation Wall Mount Horizontal InstallationLocation Positioning Your DisplayKensington Security System Antenna Connection External Equipment SetupHD Receiver Setup When connecting with a component cable480i/576iYes 480p/576pYes 720p/1080iYes 1080pYes When connecting with a Hdmi to DVI cable When connecting with a HdmiHdmi jack on the set Press the Input button to select HDMI1 or HDMI2Component Input ports DVD SetupWhen connecting Hdmi cable When connecting with an antenna VCR SetupWhen connecting with an S-Video cable When connecting with a RCA cableWhen connecting with a D-sub 15 pin cable PC SetupWhen connecting with a DVI cable Back Cover for Wire Arrangement RGB/DVIPC Hdmidtv supported modeWatching TV /PROGRAMME Control Remote Control KEY FunctionsWatching TV /PROGRAMME Control Inserting batteries into remote controlVolume Adjustment Turning on the SETProgramme Selection Setup Picture Audio On Screen Menus Selection and AdjustmentPAL I/II U.K. / Ireland / Hong Kong / South Africa Auto Programme TuningTo Set Fine Tuning Assigning a Station NameBooster Copying a programme Programme EditSelect a programme to be copied with the D / E / F / G ButtonFavourite Programme Select a desired programme with the F / G button or NumberIt, i.e.‘05’ for Selecting the Programme List Watching PIP PICTURE-IN-PICTURE Picture Size Aspect Ratiocontrol Picture ControlZoom2 Zoom1Picture Mode-Preset Preset Picture SettingsManual Picture Adjustment Level, the softer the imageTV/AV/Component/HDMI Auto Colour Tone ControlCool/Medium/Warm Colour Tone User Mode Manual Selection Picture Improvement TechnologyTo set up for the best picture quality for viewing films Advanced GammaAdvanced Blackdarkness Level Picture Reset Using OKRemocon or control key Auto Configure RGB PC mode onlyAuto Config. OK Others ResolutionManual Config Initializing Reset to original factory settings Selecting ResolutionSound Setting Adjustment -USER Mode Preset Sound SETTINGS-SOUND ModeAuto Volume Leveler TV Speakers ON/OFF SetupBalance Stereo/Dual Reception Nicam ReceptionSpeaker Sound Output Selection Auto ON/OFF Time Setting Clock SetupAuto SHUT-OFF Setting Sleep Timer SettingPress the OK button ON-SCREEN Menu Language SelectionKEY Lock Option SettingPress the G button and then D / E button to select RTC If you set ON, you enable the response time control functionFactory Reset Power IndicatorSimple Text Switch ON/OFFFastext TOP TextSelect the each index Special Teletext FunctionsRemote control Doesn’t work Power is suddenly Turned off TroubleshootingAppendix User’s guide From the web siteProduct is turned off Is the screen position Wrong?Cleaning the Screen MaintenanceCleaning the Cabinet Extended AbsenceM2394A Product SpecificationsM2794A How to Connect Remote Control IR CodesIR Codes Code Function RS-232C Setup Type of Connector D-Sub 9-Pin MaleExternal Control Through RS-232C RS-232C Configurations Set IDCommunication Parameters Transmission / Receiving Protocol Command Reference ListTransmission ka Set ID DataCr Transmission kk Set ID DataCr LSB