Mitsubishi Electronics WL6700LU, WL6700U When using the projector in Europe, Compliance Notice

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception.

Use the attached RGB cable and RS-232C cable and the shielded LAN cable with this equipment so as to keep interference within the limit of a FCC Class B device.

This apparatus must be grounded.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75.

When using the projector in Europe:

COMPLIANCE NOTICE

This projector complies with the requirements of the EC Directive 2004/108/EC “EMC Directive” and 2006/95/EC “Low Voltage Directive”.

The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.

WARNING

Use the attached RGB cable and RS-232C cable and the shielded LAN cable with this equipment so as to keep interference within the limits of an EN55022 Class B device.

Please follow WARNING instructions.

EN-2

Image 2
Contents WL6700 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Preparing your projector Checking accessoriesInserting the batteries into the remote control Control area Terminal board Preparating your projectorOverview How to disable the Laser button Bottom side Remote controlAdjustment feet Air inlet grille/Filter cover Lamp cover How to enable the Laser buttonUsing the wired remote control Using the remote controlOperational range of the remote control Reception angleWhen the aspect ratio is Full Display at 1366 x 800 pixels Setting up your projectorSetting up the screen Screen size and projection distanceWhen fine streaks are seen on projected images Setting up your projectorAdjusting the projection angle When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesFor monitor connection Plugging the power cordViewing computer images For audio output connectionProjecting images Remove the lens capTo stop projecting When connecting to a notebook computerExample of the setting procedure for external output AV muteWith the Feature menu Setting the aspect ratioHow to change the settings With the remote control To cancel the menuViewing video images Connecting the projector to video equipmentConnecting to a video player, etc Connection for video equipment having an Hdmi terminal Viewing video imagesProjector + DVD player or Hdtv decoder Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-21 Volume from the speaker Setup Menu operationMenu operation How to set the menusAvailable settings in the menus EN-25 EN-26 EN-27 EN-28 To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerHow to adjust the computer image YESTo adjust the vertical position Simple method to adjust the image positionTo adjust the horizontal position LPF Progressive filterSet the background color Advanced featuresSetting procedure Set the image sizeTo cancel the password function Advanced featuresPassword function To enable the password functionFreeze SplitMagnifying the displayed image Operation Mouse remote controlProjector + computer with USB connector Up buttonPJLink Supervising and controlling by computerProjectorView About PJLinkIndicators Normal conditionProcedure for changing batteries Terminal cover with anti-theft alarm deviceProcedure for setting the anti-theft alarm device Interval of lamp replacement Replacing the lampTo replace the lamp Reset of the lamp operation timeReplacing the lamp Cleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensTroubleshooting No image appears on the screenImages are not displayed correctly Problem Solution TroubleshootingNo image appears on the screen Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsSpecifications XGA85Without terminal cover With terminal cover ConnectorsDimension drawings unit mm Mitsubishi Projector Contact Information