Mitsubishi Electronics WL6700U Advanced features, Setting procedure, Set the background color

Page 33

Advanced features

Setting of the image displayed during startup or muting

You can display your desired image as the startup screen (or splash screen). Using the menu, you can also use such image as a background that is displayed while the video is muted or no signal is supplied.

CAPTURE : ENTER + ENTER

CANCEL : MENU

CAPTURE : ENTER + ENTER

CANCEL : MENU

12.Adjust the size of the image to be captured so that

Important:

such image stays within the red frame.

• You can’t set IMAGE CAPTURE when PASSWORD

• Press the S, T, W or X button to move the red

FUNCTION in the FEATURE menu has been set to

frame.

SPLASH ID SCREEN to enable the password lock.

• You can’t set IMAGE CAPTURE when the compo-

• You can’t move the red frame outside the

nent video signal is inputted.

screen.

Setting procedure

 

 

 

 

 

 

 

 

 

 

1.

Press the COMPUTER button to select the image

 

 

 

 

 

 

supplied to the COMPUTER/COMPONENT VIDEO

 

 

CANCEL : MENU

 

 

 

 

 

CAPTURE : ENTER + ENTER

 

 

IN terminal.

 

 

 

 

 

 

 

 

 

 

 

2.

Display your desired image.

 

 

 

 

 

13.Press the ENTER button twice.

3.

Display the INSTALLATION menu.

4.

Select IMAGE CAPTURE by pressing the S or T

• Image capture will start.

• Press the MENU button to cancel the proce-

 

button.

 

dure.

 

 

5.Press the ENTER button.

• The setting menu will be displayed.

CAPTURING IMAGE !

opt.

CAPTURE : ENTER + ENTER

CANCEL : MENU

INSTALLATION

CUSTOM IMAGE CAPTURE

BACK COLOR

GRAY

• When the image capture completes, the cap-

SIZE

x1

tured image will be displayed for three seconds.

CAPTURE

GO

 

 

 

 

Important:

 

 

 

 

 

 

 

 

Set the background color

(Set the background color only when you set the im- age size to x1 or x2.)

6.Select BACK COLOR by pressing the S or T but- ton.

7.Select your desired color for the background (GRAY,

RED, GREEN, BLUE, BLACK, WHITE, RED50%, GREEN50%, or BLUE50%) by pressing the W or X button.

Set the image size

8.Select SIZE by pressing the S or T button.

9.Select x1, x2, or FULL by pressing the W or X but- ton.

x1

x2

FULL

Capture the image

10.Select CAPTURE by pressing the S or T button. 11.Press the ENTER button.

•A red frame appears. (The size of the red frame is 640 x 374 pixels.)

•You can’t change the new startup screen back to the original startup screen. (Even when you select RESET ALL in the FEATURE menu, the factory default screen isn’t available any longer.) When you want to change the startup screen again, capture another image.

•The captured image will be displayed from the next startup. If the captured image isn’t displayed, make sure that the setting of SPLASH SCREEN in the INSTALLATION menu isn’t OFF. (See page 25.)

•To display the captured image while the video is muted, set MUTE MODE in the INSTALLATION menu to IMAGE. (See page 25.)

•When BACK COLOR in the INSTALLATION menu is set to IMAGE, the captured image will be displayed while no signal is supplied.

•In the mute mode, or when no signal is input, it takes longer time to display the captured image.

•Some images can’t be captured correctly because of their signal type.

EN-33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents WL6700 Compliance Notice When using the projector in EuropeContents Important safeguards Important safeguards Checking accessories Inserting the batteries into the remote controlPreparing your projector Preparating your projector OverviewControl area Terminal board Adjustment feet Air inlet grille/Filter cover Lamp cover Bottom side Remote controlHow to disable the Laser button How to enable the Laser buttonOperational range of the remote control Using the remote controlUsing the wired remote control Reception angleSetting up the screen Setting up your projectorWhen the aspect ratio is Full Display at 1366 x 800 pixels Screen size and projection distanceAdjusting the projection angle Setting up your projectorWhen fine streaks are seen on projected images When projected images are distorted to a trapezoidRear projection Front projection, ceiling mountingViewing computer images Connecting the projector to a computerViewing computer images Plugging the power cordFor monitor connection For audio output connectionRemove the lens cap Projecting imagesExample of the setting procedure for external output When connecting to a notebook computerTo stop projecting AV muteHow to change the settings With the remote control Setting the aspect ratioWith the Feature menu To cancel the menuConnecting the projector to video equipment Connecting to a video player, etcViewing video images Viewing video images Projector + DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Connection for video equipment having a DVI-D terminal Plugging in the power cordEN-21 Volume from the speaker Menu operation SetupHow to set the menus Available settings in the menusMenu operation EN-25 EN-26 EN-27 EN-28 To adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature Color EnhancerYES How to adjust the computer imageTo adjust the horizontal position Simple method to adjust the image positionTo adjust the vertical position LPF Progressive filterSetting procedure Advanced featuresSet the background color Set the image sizePassword function Advanced featuresTo cancel the password function To enable the password functionSplit Magnifying the displayed imageFreeze Projector + computer with USB connector Mouse remote controlOperation Up buttonProjectorView Supervising and controlling by computerPJLink About PJLinkNormal condition IndicatorsTerminal cover with anti-theft alarm device Procedure for setting the anti-theft alarm deviceProcedure for changing batteries Replacing the lamp Interval of lamp replacementReset of the lamp operation time Replacing the lampTo replace the lamp Cleaning of the air-filter MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensNo image appears on the screen TroubleshootingTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Kensington Lock Others Problem SolutionSpecifications Replacement part option/not included in the boxXGA85 SpecificationsConnectors Dimension drawings unit mmWithout terminal cover With terminal cover Mitsubishi Projector Contact Information
Top Page Image Contents