Mitsubishi Electronics WD510U-G Preparation for projection, Using the adjustment feet front

Page 13

Preparation

Preparation for projection

1.Attach the provided power cord to the projector.

2.Plug the power cord in the wall outlet.

3.Remove the lens cap.

Warning:

•Do not look into the lens directly when the projector is on.

•The lens cap is for protecting the lens. If you leave the lens cap on the lens with the projector turned on, it may be deformed because of heat build-up. Remove the lens cap when you turn on the pro- jector.

•One of power cords for the U.S., Europe and U.K. is provided appropriately.

•This projector uses the power plug of three-pin grounding type. Do not remove the grounding pin from the power plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.

•In case that the power cord for the U.S is provided with this projec- tor, never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If you want to use a power supply using other voltage than rated, prepare an appropri- ate power cord separately.

•Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.

•Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause fire or electric shock.

•Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.

Caution:

•Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.

•Do not plug in or out the power cord with your hand wet. It may cause electric shock.

Adjustment of the projection angle

For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector.

Using the adjustment feet (front)

1.Tilt up the projector to the appropriate angle.

2.Press the foot adjustment button (front).

3.Release the foot adjustment button (front) after fine adjusting a position of lengthwise direction of the image.

Using the adjustment feet (rear)

1.Tilt up the projector to the appropriate angle.

2.Rotate the adjustment feet (rear) for fine adjustment.

Important:

•Install the screen on a flat wall at 90 degrees to the floor.

•Slanting the projector more than ±10° (right and left) or ±15° (front and rear) may cause trouble or explosion of the lamp. You can tilt the projector up to 8 degrees using the adjustment feet only.

•Images may not be projected in a shape of a regular rectangle or with its aspect ratio 4:3, depending on the installation conditions of the projector and the screen.

•To correct vertical keystone distortion, press the KEYSTONE but-

ton on the projector or the remote control to display KEYSTONE, and adjust the image by pressing the S, T button (or VOLUME S, T button on the remote control).

In the following cases:

Press the T

Press the S

button.

button.

Important:

•When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean a projection angle.

•The allowable range of the adjustment value in the keystone adjustment varies depending on the installation conditions.

•When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines may bend in images with complicated patterns. They are not due to product malfunctions.

•Noise may appear on the screen during the keystone adjustment because of the type of the video signal being projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in the range where the image is dis- played without noise.

•When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal.

•The keystone adjustment range in the minus direction is narrower than that in the plus direction.

ENGLISH

Foot adjustment button

After using the projector:

4.Put the adjustment feet (front) back into the projector by pressing the foot adjustment buttons.

EN-13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents WD510U/WD510U-G Shock When using the projector in Europe only for WD510UContents Important safeguards Do not look into the lens when the projector is operating Do not keep using the damaged projectorDo not unplug the power cord during operation Place of installationControl panel OverviewTerminal board 12 6Overview Remote controlBottom side Battery installation Remote controlOperation range of the remote control When the aspect ratio of the screen is InstallationWhen the aspect ratio of the image is 1610 Wxga Layout of the projectorWhen the aspect ratio of the image is InstallationFront projection, ceiling mounting Rear projectionProjector + AV device Basic connectionsProjector + DVD player or Hdtv decoder Projector + Computer Basic connectionsUsing the adjustment feet front Adjustment of the projection angleUsing the adjustment feet rear PreparationWhen fine streaks are seen on projected images Power-onStatus Power Basic operationBasic operation Wall Screen When connecting to a laptop computerContrast Menu operationAuto Theater UserBasic operation Menu operationMenu Options Image menuInstallation menu Feature menu Singal menu Signal User menuInformation menu Adjusting projected images Image adjustmentGamma mode Color EnhancerSimple method to adjust the image position Image adjustmentBrilliantColorTM LPF Progressive filterFreeze Advanced featuresTo cancel the password function Advanced featuresTo use the Magnify mode MagnifyWhen the projector is mounted to the ceiling Lamp replacementInterval of lamp replacement Lamp replacementReset of the lamp operation time Power Status TroubleshootingNo image appears on the screen Images are not displayed correctly TroubleshootingLPF Cleaning of the projector and the ventilation slots MaintenanceCleaning of the lens OthersNormal condition IndicatorsAbnormal condition DVI-D SpecificationsConnectors SpecificationsDimensional drawings unit mm CGA85 CGA84VGA60 VGA72Mitsubishi Electric Corporation
Related manuals
Manual 6 pages 16.6 Kb

WD510U-G specifications

The Mitsubishi Electronics WD510U-G is an advanced DLP (Digital Light Processing) projector that boasts impressive performance and cutting-edge technology tailored for a variety of applications. It is particularly well-suited for educational environments, corporate settings, and professional presentations, offering users an engaging visual experience.

One of the standout features of the WD510U-G is its high brightness capability, with a luminous output of up to 5,000 ANSI lumens. This capability ensures that images remain clear and vibrant even in well-lit environments, making it an ideal choice for larger rooms or venues where ambient light can often compromise visual quality.

The projector offers a native resolution of WXGA (1280 x 800), which is optimized for widescreen content, allowing users to display presentations, videos, and images with sharp detail and clarity. Additionally, the WD510U-G supports a range of resolutions, including HD, making it versatile enough to handle various content types.

Another hallmark of the WD510U-G is its exceptional contrast ratio of 3000:1, which enhances the depth and richness of images. This is particularly beneficial for presentations that rely on detailed graphics or video content, as it helps to ensure that dark areas remain distinct and colors appear vibrant.

Mitsubishi has also included a range of connectivity options in the WD510U-G, including HDMI, VGA, and USB ports, facilitating seamless integration with various input devices such as laptops, video players, and gaming consoles. This versatility allows users to quickly switch between different sources without the hassle of complex setups.

In terms of maintenance, the WD510U-G features a long-lasting lamp life of up to 5,000 hours in normal mode and up to 6,000 hours in eco mode. This extended lamp life reduces the need for frequent replacements, thereby lowering overall operating costs and ensuring consistent performance over time.

The projector is designed with user-friendly features, including an intuitive remote control and on-screen menus, which simplify the setup process and enhance user experience. Additionally, its compact and lightweight design makes it easy to transport, ideal for mobile professionals and educators.

In conclusion, the Mitsubishi Electronics WD510U-G is a powerful and reliable DLP projector that combines high brightness, excellent resolution, and versatile connectivity, making it a top choice for anyone seeking to deliver compelling presentations or display engaging content in a variety of settings. With its advanced technology and user-friendly features, it stands out as an essential tool for modern communication.
Top Page Image Contents