Mitsubishi Electronics WD510U-G Troubleshooting, No image appears on the screen, Power Status

Page 28

Troubleshooting

Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the power plug, and then contact your dealer.

No image appears on the screen.

Problem

Solution

 

 

•Check whether the indicators are on or off and how they are lightning.

 

 

POWER

 

STATUS

Solution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connect the power cord to the projector.

 

 

 

Off

 

 

Off

Plug the power cord into a wall outlet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If any objects are blocking the air inlet or outlet grille, remove them and carry out

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the following.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Unplug the power cord from the wall outlet.

 

 

 

 

 

 

 

 

 

 

Off

2. Make sure that the projector has cooled off.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3. Plug the power cord into the wall outlet.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4. Press the POWER button.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If any objects are blocking the air inlet or outlet grille, remove them.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Blinking

Don't expose the air outlet grilles to hot air emitted from a heating appliance.

 

 

 

 

 

 

 

 

 

 

 

Power can not be turned on.

 

 

 

 

 

 

 

orange

 

 

 

Steady red

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

After the STATUS indicator stops blinking, press the POWER button.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If you unplug the power cord while the fan is rotating, the lamp may not turn on about 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Blinking

minute when you plug the power cord next time.

 

 

 

 

 

 

 

 

 

The lamp can't turn on again for 1 minute after it goes out.

 

 

 

 

 

 

 

 

 

green

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press the POWER button several times.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace the lamp. (The lamp is at the end of its life.)

 

 

 

 

 

 

 

 

 

Steady red

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Attach the lamp cover on the top.

 

 

 

 

 

 

 

 

 

 

Off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unplug the power cord from the wall outlet and contact your dealer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Blinking red

 

Steady

 

 

 

 

/ green

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Blinking

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Cancel the AV mute by pressing the AV MUTE button.

 

• Check that the lens cap is removed.

 

• It may take about 1 minute for the lamp to light up.

 

• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

 

• If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotat-

 

ing and the POWER button may not work after the power cord is plugged. After the fan stops rotating, press

No image appears on the screen.

the POWER button to turn back on the POWER indicator.

 

• Set SCART INPUT in the FEATURE menu to OFF. (See page 20.)

 

• Check that the intake vent is clean.

 

• Check that the lamp cover is closed. (See page 27.)

 

• Check that the cables connected to the external devices are not broken.

 

• When an extension cable is being used, replace it with the supplied cable for check.

 

• When images are displayed correctly, add an RGB signal amplifier to the extension cable.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• This problem may occur when the intake vent and/or exhaust vents are blocked. (In such a case, the STATUS

 

indicator brinks orange.)

 

J Remove the objects blocking the intake vent and/or exhaust vents and then carry out the following proce-

 

 

dure.

 

 

 

 

 

 

 

 

 

1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator goes out.)

 

2. Unplug the power cord from the wall outlet.

Power turns off.

3. Wait about 10 minutes.

 

4. Plug the power cord into the wall outlet.

 

5. Press the POWER button.

 

• When the STATUS indicator is steady red, it is indicating that the lamp should be replaced. Replace the lamp

 

in this case.

 

 

 

 

 

 

 

 

 

• Check that AUTO POWER OFF has been set to OFF.

 

• If the lamp has deteriorated, it may go out after a while it illuminates.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT to enable the password

The screen for entering the password appears.

lock.

 

 

 

 

 

 

 

 

J Enter the password or contact the person in charge of management of the projector.

 

 

(See page 24.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Turn on the power of the connected device, or check whether there is something wrong with the connected

 

device.

 

 

 

 

 

 

 

 

 

• Check whether the external device output signals. (Check this especially when the external device is a note-

 

book computer.)

 

 

"NO SIGNAL" is displayed.

• Check that the cable connected to the external device isn’t defective.

 

• Check that the projector is connected to the external device using the correct terminals.

 

• Check that the connected device is correctly selected as the input source.

 

• When an extension cord is being used, replace it with the supplied cable and check whether images are pro-

 

jected correctly. If images are projected correctly, use an RGB signal amplifier along with the extension cord.

EN-28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents WD510U/WD510U-G When using the projector in Europe only for WD510U ShockContents Important safeguards Do not keep using the damaged projector Do not look into the lens when the projector is operatingDo not unplug the power cord during operation Place of installationOverview Control panelTerminal board 12 6Overview Remote controlBottom side Battery installation Remote controlOperation range of the remote control Installation When the aspect ratio of the screen isWhen the aspect ratio of the image is 1610 Wxga Layout of the projectorInstallation When the aspect ratio of the image isFront projection, ceiling mounting Rear projectionProjector + AV device Basic connectionsProjector + DVD player or Hdtv decoder Basic connections Projector + ComputerAdjustment of the projection angle Using the adjustment feet frontUsing the adjustment feet rear PreparationPower-on When fine streaks are seen on projected imagesStatus Power Basic operationBasic operation When connecting to a laptop computer Wall ScreenMenu operation ContrastAuto Theater UserMenu operation Basic operationMenu Options Image menuInstallation menu Feature menu Singal menu Signal User menuInformation menu Image adjustment Adjusting projected imagesGamma mode Color EnhancerImage adjustment Simple method to adjust the image positionBrilliantColorTM LPF Progressive filterAdvanced features FreezeAdvanced features To cancel the password functionTo use the Magnify mode MagnifyLamp replacement When the projector is mounted to the ceilingInterval of lamp replacement Lamp replacementReset of the lamp operation time Power Status TroubleshootingNo image appears on the screen Images are not displayed correctly TroubleshootingLPF Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens OthersNormal condition IndicatorsAbnormal condition Specifications DVI-DConnectors SpecificationsDimensional drawings unit mm CGA84 CGA85VGA60 VGA72Mitsubishi Electric Corporation
Related manuals
Manual 6 pages 16.6 Kb

WD510U-G specifications

The Mitsubishi Electronics WD510U-G is an advanced DLP (Digital Light Processing) projector that boasts impressive performance and cutting-edge technology tailored for a variety of applications. It is particularly well-suited for educational environments, corporate settings, and professional presentations, offering users an engaging visual experience.

One of the standout features of the WD510U-G is its high brightness capability, with a luminous output of up to 5,000 ANSI lumens. This capability ensures that images remain clear and vibrant even in well-lit environments, making it an ideal choice for larger rooms or venues where ambient light can often compromise visual quality.

The projector offers a native resolution of WXGA (1280 x 800), which is optimized for widescreen content, allowing users to display presentations, videos, and images with sharp detail and clarity. Additionally, the WD510U-G supports a range of resolutions, including HD, making it versatile enough to handle various content types.

Another hallmark of the WD510U-G is its exceptional contrast ratio of 3000:1, which enhances the depth and richness of images. This is particularly beneficial for presentations that rely on detailed graphics or video content, as it helps to ensure that dark areas remain distinct and colors appear vibrant.

Mitsubishi has also included a range of connectivity options in the WD510U-G, including HDMI, VGA, and USB ports, facilitating seamless integration with various input devices such as laptops, video players, and gaming consoles. This versatility allows users to quickly switch between different sources without the hassle of complex setups.

In terms of maintenance, the WD510U-G features a long-lasting lamp life of up to 5,000 hours in normal mode and up to 6,000 hours in eco mode. This extended lamp life reduces the need for frequent replacements, thereby lowering overall operating costs and ensuring consistent performance over time.

The projector is designed with user-friendly features, including an intuitive remote control and on-screen menus, which simplify the setup process and enhance user experience. Additionally, its compact and lightweight design makes it easy to transport, ideal for mobile professionals and educators.

In conclusion, the Mitsubishi Electronics WD510U-G is a powerful and reliable DLP projector that combines high brightness, excellent resolution, and versatile connectivity, making it a top choice for anyone seeking to deliver compelling presentations or display engaging content in a variety of settings. With its advanced technology and user-friendly features, it stands out as an essential tool for modern communication.
Top Page Image Contents