Mitsubishi Electronics XD530U Preparation for projection, Adjustment of the projection angle

Page 14

Preparation

Preparation for projection

1.Attach the provided power cord to the projector.

2.Plug the power cord in the wall outlet.

3.Remove the lens cap.

Warning:

Do not look into the lens directly when the projector is on.

The lens cap is for protecting the lens. If you leave the lens cap on the lens with the projector turned on, it may be deformed because of heat build-up. Remove the lens cap when you turn on the pro- jector.

One of power cords for the U.S., Europe and U.K. is provided appropriately.

This projector uses the power plug of three-pin grounding type. Do not remove the grounding pin from the power plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.

In case that the power cord for the U.S is provided with this projec- tor, never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If you want to use a power supply using other voltage than rated, prepare an appropri- ate power cord separately.

Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.

Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause fire or electric shock.

Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.

Caution:

Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.

Do not plug in or out the power cord with your hand wet. It may cause electric shock.

Adjustment of the projection angle

For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector.

Using the adjustment feet (front)

1.Tilt up the projector to the appropriate angle.

2.Press the foot adjustment button (front).

3.Release the foot adjustment button (front) after fine adjusting a position of lengthwise direction of the image.

Using the adjustment feet (rear)

1.Tilt up the projector to the appropriate angle.

2.Rotate the adjustment feet (rear) for fine adjustment.

Important:

Install the screen on a flat wall at 90 degrees to the floor.

Slanting the projector more than ±10° (right and left) or ±15° (front and rear) may cause trouble or explosion of the lamp. You can tilt the projector up to 8 degrees using the adjustment feet only.

Images may not be projected in a shape of a regular rectangle or with its aspect ratio 4:3, depending on the installation conditions of the projector and the screen.

To correct vertical keystone distortion, press the KEYSTONE but-

ton on the projector or the remote control to display KEYSTONE, and adjust the image by pressing the S, T button (or VOLUME S, T button on the remote control).

In the following cases:

Press the T

Press the S

button.

button.

Important:

When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean a projection angle.

The allowable range of the adjustment value in the keystone adjustment varies depending on the installation conditions.

When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines may bend in images with complicated patterns. They are not due to product malfunctions.

Noise may appear on the screen during the keystone adjustment because of the type of the video signal being projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in the range where the image is dis- played without noise.

When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal.

Foot adjustment button

After using the projector:

4.Put the adjustment feet (front) back into the projector by pressing the foot adjustment buttons.

EN-14

Image 14
Contents XD530U/XD530E When using the projector in Europe only for XD530E ShockContents Important safeguards Do not unplug the power cord during operation Do not keep using the damaged projectorDo not look into the lens when the projector is operating Place of installationRegulatory statement R&TTE Model Name XD530UKensington Lock OverviewControl panel Terminal board Bottom side Remote control OverviewOperation range of the remote control Remote controlBattery installation Reception angle verticalFront projection InstallationLayout of the projector Front projection, ceiling mountingVideo Basic connectionsProjector + AV device AUDIO-INCOMPUTER-IN Basic connectionsProjector + DVD player or Hdtv decoder Projector + Computer Using the adjustment feet rear Adjustment of the projection angleUsing the adjustment feet front PreparationStatus Power Power-onWhen fine streaks are seen on projected images Basic operationBasic operation When connecting to a laptop computer Wall ScreenSafety instructions for wireless Security measures Security precautions for wirelessAbout wireless LAN network Software license agreement for wireless Projecting images wirelessly Projecting images Projecting images wirelesslyInstalling the connection software Running the connection softwareIf the wireless connection fails How to use the connection software Displaying the version information of the software How to use the connection softwareDisplaying the information about the projector Downloading the connection software How to use the administration screenConfiguring the projector Selecting the image to be projectedWEP How to use the administration screenChanging the network settings Restoring the default settings Changing the settings for the projectionChanging the password Uninstalling the connection software How to use wired LAN connection For Ethernet connectionMenu operation Menu Options Menu operationBasic operation Image menuInstallation menu Feature menu Singal menu Signal User menuWireless menu Information menuGamma mode Image adjustmentAdjusting projected images Color EnhancerBrilliantColorTM Image adjustmentSimple method to adjust the image position LPF Progressive filterAdvanced features FreezeTo use the Magnify mode Advanced featuresTo cancel the password function MagnifyLamp replacement When the projector is mounted to the ceilingReset of the lamp operation time Lamp replacementInterval of lamp replacement No image appears on the screen TroubleshootingPower Status LPF TroubleshootingImages are not displayed correctly Projector cannot be connected wirelessly OthersCleaning of the lens MaintenanceCleaning of the projector and the ventilation slots Abnormal condition IndicatorsNormal condition Specifications DVI-DDimensional drawings unit mm SpecificationsConnectors What’s included in the boxVGA60 CGA84CGA85 VGA72Mitsubishi Electric Corporation