Mitsubishi Electronics XD530U, XD530E user manual Projector cannot be connected wirelessly, Others

Page 44

Troubleshooting (continued)

The projector cannot be connected wirelessly.

 

Problem

Solution

 

 

 

The wireless function of your computer is not avail-

 

 

able.

• Some computers are equipped with a wireless power switch. Turn the switch ON.

The wireless connection icon of your computer is

• Select and right-click the "Wireless Network Connection" icon. If the properties are disabled, select "Enable".

 

not displayed.

• Some computers allow you to select Disable/Enable for the wireless function using BIOS. For more details,

"Wireless Projector" is not displayed in "View

see the manual of your computer.

 

Available Wireless Networks".

• Perform NETWORK RESET in the WIRELESS menu of the projector.

The message "No any wireless card can be used"

• Set POWER MODE of the projector to ON.

 

appears.

 

 

 

 

 

 

• Display the "Wireless Network Connection" properties of your computer, and then check that "Obtain an IP

 

 

address automatically" and "Obtain DNS server address automatically" are selected in the "Internet Protocol

The message "No Projector Found" or "Network is

(TCP/IP)" properties.

• If you changed the network setup settings in the system administrator screen for the Web, change the proper-

not available" appears.

ties of "Wireless Network Connection" in your computer according to the changed settings.

 

 

 

 

• Perform NETWORK RESET in the WIRELESS menu of the projector.

 

 

• Set POWER MODE of the projector to ON.

 

 

The message "Due to your network or firewall set-

 

ting, the client application cannot connect to the pro-

• Open the "Windows Firewall" dialog box from "Control Panel" of your computer, and then check that the

jection server. Please check related settings to allow

"Wireless Projector" check box is selected in the "Programs and Services" list in the [Exceptions] tab.

this application to be able to communicate with the

 

server!" appears.

 

 

 

 

 

 

• Switch the input source of the projector to "WIRELESS".

The SSID name of this projector is not displayed for

• Set POWER MODE to ON or AUTO in the menu for the wireless function of the projector.

• If the reception status is poor, move the projector closer to the computer, or make sure that no obstacle exists

the available access point.

between the projector and the computer.

 

 

 

 

• Enable the SSID broadcast in the network setup.

 

 

 

 

 

• Depending on the security software, a function to prevent access to Phishing sites is provided. Disable the

 

 

function while using the projector.

 

 

• Confirm that the Server IP of the projector is different from the IP address of your computer.

 

 

• Make sure that the first three digits of the Server IP of the projector are the same as those of the IP address

You cannot log on the screen.

of your computer.

The Web screen "Wireless Projector" is not dis-

(Example: the Server IP of the projector: 192.168.100.10; the IP address of your computer: 192.168.100.15)

 

played.

• Make sure that the correct Web address is entered.

The IP of the wireless projector is displayed as

(Make sure that "www" is not included in the address.)

 

0.0.0.0 in the login screen.

• If the above screen is not displayed, select and right-click the "Wireless Network Connection" icon of your

 

 

computer to display the properties, select "Internet Protocol (TCP/IP)", and then check that "Obtain an IP

 

 

address automatically" and "Obtain DNS server address automatically" are selected in the properties.

 

 

• Perform NETWORK RESET in the WIRELESS menu of the projector.

 

 

• Set POWER MODE of the projector to ON.

 

 

 

The Web page "Wireless Projector" is not displayed

• If your computer is set to a static IP or is used in a DHCP environment, enter the Server IP displayed in the

default screen of the wireless connection.

even if you run the Web browser.

• Select the [Tools] menu → [Internet Options] → [Security] → [Custom Level] to set [Allow META REFRESH]

 

 

to [Enable].

 

 

You cannot install the connection software.

• Log on as a user with administrator rights.

 

 

The projector cannot be connected wirelessly.

• Check if any network bridge is used.

 

 

Others

 

 

Problem

Solution

 

 

The exhaust vents emit warm air.

• This air comes out after cooling the inside of the projector. You may feel hot, but this is not a malfunction.

 

 

No audio is output.

• Check that the volume isn’t set to low.

 

 

 

 

 

• The microcomputers inside the projector may be wrongly operating because of noise.

The menu can’t be used.

J Press the POWER button to turn off the lamp and unplug the power cord from the wall outlet. Wait about

 

 

10 minutes, plug the power cord in, and try again.

 

 

 

 

 

• This indication appears when the ambient temperature rises high. When the ambient temperature stays high,

 

 

the lamp goes out.

"TEMPERATURE!!" is displayed.

J Eliminate any causes of the rise in the ambient temperature.

• This indication appears when the air inlet or outlet grille is blocked. When they are kept blocked, the lamp

 

 

 

 

goes out.

 

 

J Remove the objects blocking the air inlet or outlet grille.

 

 

 

The

mark appears.

• This mark appears when ineffective operation is carried out. This isn’t a product malfunction.

 

 

 

 

 

• Check that the batteries are loaded in the remote control or the batteries are not weak. (See page 9.)

The remote control doesn’t function easily or at all.

• Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light. (See page 9.)

• Use the remote control within its operation range. (See page 9.)

 

 

 

 

• Use the remote control at least 10 cm away from the projector.

 

 

 

 

 

• PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to enable the password

The buttons on the control panel (except for the

lock.

POWER button) don’t function.

J Cancel the password lock or contact the person in charge of management of the projector.

 

 

(See page 39.)

 

 

 

Abnormal sound is heard.

• Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions. Such symp-

tom is not a malfunction.

 

 

 

 

 

EN-44

Image 44
Contents XD530U/XD530E When using the projector in Europe only for XD530E ShockContents Important safeguards Do not keep using the damaged projector Do not look into the lens when the projector is operatingDo not unplug the power cord during operation Place of installationRegulatory statement R&TTE Model Name XD530UKensington Lock OverviewControl panel Terminal board Bottom side Remote control OverviewRemote control Battery installationOperation range of the remote control Reception angle verticalInstallation Layout of the projectorFront projection Front projection, ceiling mountingBasic connections Projector + AV deviceVideo AUDIO-INCOMPUTER-IN Basic connectionsProjector + DVD player or Hdtv decoder Projector + Computer Adjustment of the projection angle Using the adjustment feet frontUsing the adjustment feet rear PreparationPower-on When fine streaks are seen on projected imagesStatus Power Basic operationBasic operation When connecting to a laptop computer Wall ScreenSafety instructions for wireless Security measures Security precautions for wirelessAbout wireless LAN network Software license agreement for wireless Projecting images wirelessly Projecting images wirelessly Installing the connection softwareProjecting images Running the connection softwareIf the wireless connection fails How to use the connection software Displaying the version information of the software How to use the connection softwareDisplaying the information about the projector How to use the administration screen Configuring the projectorDownloading the connection software Selecting the image to be projectedWEP How to use the administration screenChanging the network settings Restoring the default settings Changing the settings for the projectionChanging the password Uninstalling the connection software How to use wired LAN connection For Ethernet connectionMenu operation Menu operation Basic operationMenu Options Image menuInstallation menu Feature menu Signal User menu Wireless menuSingal menu Information menuImage adjustment Adjusting projected imagesGamma mode Color EnhancerImage adjustment Simple method to adjust the image positionBrilliantColorTM LPF Progressive filterAdvanced features FreezeAdvanced features To cancel the password functionTo use the Magnify mode MagnifyLamp replacement When the projector is mounted to the ceilingReset of the lamp operation time Lamp replacementInterval of lamp replacement No image appears on the screen TroubleshootingPower Status LPF TroubleshootingImages are not displayed correctly Projector cannot be connected wirelessly OthersCleaning of the lens MaintenanceCleaning of the projector and the ventilation slots Abnormal condition IndicatorsNormal condition Specifications DVI-DSpecifications ConnectorsDimensional drawings unit mm What’s included in the boxCGA84 CGA85VGA60 VGA72Mitsubishi Electric Corporation