Mitsubishi Electronics XD530E Remote control, Battery installation, Reception angle vertical

Page 9

Remote control

Battery installation

Use two (AA, R6) size batteries.

1.Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.

2.Load the batteries making sure that they are positioned correctly (+ to +, and - to -).

• Load the batteries from - spring side, and make sure to set them tightly.

3.Replace the back cover.

Caution:

Use of a battery of wrong type may cause explosion.

Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

Dispose of used batteries according to your local regulations.

Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.

Be sure to handle the battery according to the instructions.

Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the battery, if the remote control is not used for a long time.

Do not combine a new battery with an old one.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

Operation range (of the remote control)

The maximum operation distance of the remote control is about 10 m (or about 32 feet) when the remote control is pointed at the remote control sensor of the projector. When the remote control is pointed to the screen, the distance from the remote control to the projector via the screen should be 5 m or less. However, the operation distance varies depending on the type of the screen used.

Reception angle (vertical)

ENGLISH

Reception angle (horizontal)

Reception angle (vertical), ceiling mount

Important:

Do not expose the remote control sensor to direct sunlight or fluorescent. Keep a distance at least 2 m (6.5 feet) between the remote control sen- sor and the fluorescent light to ensure correct operation of the remote control.

Inverted fluorescent light, if located near the projector, may interfere the remote control.

When you use the remote control too close to the remote control sensor, the remote control may not work correctly.

EN-9

Image 9
Contents XD530U/XD530E Shock When using the projector in Europe only for XD530EContents Important safeguards Do not look into the lens when the projector is operating Do not keep using the damaged projectorDo not unplug the power cord during operation Place of installationModel Name XD530U Regulatory statement R&TTEOverview Control panel Terminal boardKensington Lock Overview Bottom side Remote controlBattery installation Remote controlOperation range of the remote control Reception angle verticalLayout of the projector InstallationFront projection Front projection, ceiling mountingProjector + AV device Basic connectionsVideo AUDIO-INBasic connections Projector + DVD player or Hdtv decoderCOMPUTER-IN Projector + Computer Using the adjustment feet front Adjustment of the projection angleUsing the adjustment feet rear PreparationWhen fine streaks are seen on projected images Power-onStatus Power Basic operationBasic operation Wall Screen When connecting to a laptop computerSafety instructions for wireless Security precautions for wireless About wireless LAN networkSecurity measures Software license agreement for wireless Projecting images wirelessly Installing the connection software Projecting images wirelesslyProjecting images Running the connection softwareIf the wireless connection fails How to use the connection software How to use the connection software Displaying the information about the projectorDisplaying the version information of the software Configuring the projector How to use the administration screenDownloading the connection software Selecting the image to be projectedHow to use the administration screen Changing the network settingsWEP Changing the settings for the projection Changing the passwordRestoring the default settings Uninstalling the connection software For Ethernet connection How to use wired LAN connectionMenu operation Basic operation Menu operationMenu Options Image menuInstallation menu Feature menu Wireless menu Signal User menuSingal menu Information menuAdjusting projected images Image adjustmentGamma mode Color EnhancerSimple method to adjust the image position Image adjustmentBrilliantColorTM LPF Progressive filterFreeze Advanced featuresTo cancel the password function Advanced featuresTo use the Magnify mode MagnifyWhen the projector is mounted to the ceiling Lamp replacementLamp replacement Interval of lamp replacementReset of the lamp operation time Troubleshooting Power StatusNo image appears on the screen Troubleshooting Images are not displayed correctlyLPF Others Projector cannot be connected wirelesslyMaintenance Cleaning of the projector and the ventilation slotsCleaning of the lens Indicators Normal conditionAbnormal condition DVI-D SpecificationsConnectors SpecificationsDimensional drawings unit mm What’s included in the boxCGA85 CGA84VGA60 VGA72Mitsubishi Electric Corporation