Mitsubishi Electronics XD3200U user manual Replacing the lamp, To replace the lamp

Page 44

Replacing the lamp (continued)

To replace the lamp:

1.Turn off the main power switch and unplug the power cord.

2.Loosen the screw (a) using a Phillips screwdriver

(+), and remove the lamp cover (b).

(b)

(a)

3.Loosen the screws (c) using a Phillips screwdriver

(+).

(c)

4.Pull the handle.

5.Pull out the lamp box by the handle while holding the projector.

Pull the lamp box out of the projector slowly. If it is pulled out quickly, the lamp may break scattering glass fragments.

Do not spill liquid on the removed lamp box or do not place it near any flammable object or where children can reach to prevent injury or fire.

6.Load a new lamp box securely into the projector in the right orientation.

7.Put the handle back to the original position.

Make sure that the handle is locked.

8.Tighten up the screws (c) using a Phillips screwdriver (+).

(c)

9.Tighten up the screw (a) using a Phillips screwdriver

(+) to secure the lamp cover (b).

(b)

(a)

Reset of the lamp operation time

10.Plug the power cord into the wall outlet and turn on the main power switch.

11.Press the t, , and POWER button on the projector at the same time.

Important:

Unless these 3 buttons are pressed at the same time, the lamp operation time isn’t reset.

Make sure that the STATUS indicator blinks twice and the lamp operation time is reset successfully.

The projector doesn’t turn on if the lamp cover isn’t attached securely.

Be sure to reset the lamp operation time whenever you replace the lamp.

Do not reset the lamp operation time unless you replace the lamp.

The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.

Caution:

This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)

EN-44

Image 44
Contents XD3200 EN-2 Contents Important safeguards Important safeguards Do not keep using the damaged projectorPreparing your projector Checking accessoriesInserting the batteries into the remote control 1112 Power jack Main power switch Preparating your projectorOverview Control areaAbout the laser beam Remote controlBottom side Using the remote control Operational range of the remote controlUsing the wired remote control Reception angleSetting up your projector Setting up the screenScreen size and projection distance Front projectionSetting up your projector Adjusting the position of the projected imageWhen fine streaks are seen on projected images When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesAbout DDC For monitor connectionInstalling the terminal cover Projecting images Remove the lens capTo stop projecting Instant Shut DownWhen connecting to a notebook computer Setting of the resolutionExample of the setting procedure for external output AV muteConnecting the projector to video equipment Connecting to a video player, etcWhen using the BNC connector When a TV tuner or VCR is connectedConnection for video equipment having an Hdmi terminal Viewing video imagesProjector + DVD player or Hdtv decoder Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-22 EN-23 How to change the settings With the remote control Volume from the speakerSetting the aspect ratio Menu display mode and menu type Menus displayed in the Quick Menu modeMenus displayed in the Detail Menu mode Menu operationBasic procedure for setting the menus Menu operationSettings of each menu item Quick MenuEN-28 Image menu Advanced MenuEN-30 EN-31 Signal menu UserAdjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To adjust the tone of white Color TempColor Enhancer Adjusting projected imagesAbout color temperature How to adjust the computer image YESSimple method to adjust the image position To adjust the horizontal positionTo adjust the vertical position LPF Progressive filterAdvanced features Setting procedureAdvanced features Password functionTo enable the password function To cancel the password functionFreeze Picture in Picture PinPMagnifying the displayed image Mouse remote control Projector + computer with USB connectorOperation UP buttonConnection Supervising and controlling by computerMajor functions Abnormal condition IndicatorsNormal condition Interval of lamp replacement Replacing the lampTo replace the lamp Reset of the lamp operation timeReplacing the lamp Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens When removing the lamp from the ceiling-mounted projectorTroubleshooting No image appears on the screen Problem SolutionTroubleshooting Images are not displayed correctly Problem SolutionOthers Problem Solution EN-49 Specifications Replacement part option/not included in the boxSpecifications XGA85Without terminal cover ConnectorsDimension drawings unit mm Mitsubishielectric Corporation
Related manuals
Manual 17 pages 20.86 Kb