Mitsubishi Electronics XD3200U user manual Preparing your projector, Checking accessories

Page 6

Preparing your projector

Checking accessories

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.

Cables

Mini D-SUB 15-pin

Mini D-SUB

15-pin

RGB cable for PC (246C597-10)

D-SUB 9-pin

D-SUB 9-pin

RS-232C cable

(246C598-10)

Used for projector control by computer.

Power supply parts

Power cord (two)

(246C483-10, 246C383-20)

Remote control parts

Remote control

R6 (size-AA)

(290P176-10)

battery (two)

Others

Lens cap (attached to the projector)

Terminal cover (750B017-10)

Lamp replacement tray (857C132-10)

CD-ROM (919C165-10)

Safety Manual/Quick Start up (871D531-10)

Important:

• The attached power cords are to be used exclusively for this product. Never use them for other products.

Inserting the batteries into the remote control

1

1.

Remove the rear lid of the remote control.

2.

Check the polarity (+), (-) of the batteries, and set them

 

3

correctly, inserting their (-) side first.

 

 

• If the battery is inserted from the (+) side first, inserting

 

 

the (-) side is difficult because the coil spring end hits

 

 

on the battery side. If the battery is forced to insert in

 

2

this way, the outer label of the battery may get ripped

 

and it may cause a short-circuit and heating.

 

 

 

3.

Attach the rear lid.

 

Important:

 

Use two size-AA batteries (R6).

 

Replace the 2 batteries with new ones when the remote

 

 

control is slow to operate.

Removing the batteries from the remote control Remove the back lid of the remote control and take out the batteries.

Caution:

Use of a battery of wrong type may cause explosion.

Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

Dispose of used batteries according to your local regulations.

Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fire.

Be sure to handle the batteries according to the instructions.

Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the batteries, if the remote control is not used for a long time.

Do not combine a new battery with an old one.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

EN-6

Image 6
Contents XD3200 EN-2 Contents Important safeguards Important safeguards Do not keep using the damaged projectorChecking accessories Inserting the batteries into the remote controlPreparing your projector Overview 1112 Power jack Main power switchPreparating your projector Control areaRemote control Bottom sideAbout the laser beam Using the wired remote control Using the remote controlOperational range of the remote control Reception angleScreen size and projection distance Setting up your projectorSetting up the screen Front projectionWhen fine streaks are seen on projected images Setting up your projectorAdjusting the position of the projected image When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesAbout DDC Plugging the power cordViewing computer images For monitor connectionInstalling the terminal cover Projecting images Remove the lens capTo stop projecting Instant Shut DownExample of the setting procedure for external output When connecting to a notebook computerSetting of the resolution AV muteWhen using the BNC connector Connecting the projector to video equipmentConnecting to a video player, etc When a TV tuner or VCR is connectedViewing video images Projector + DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-22 EN-23 Volume from the speaker Setting the aspect ratioHow to change the settings With the remote control Menus displayed in the Detail Menu mode Menu display mode and menu typeMenus displayed in the Quick Menu mode Menu operationBasic procedure for setting the menus Menu operationSettings of each menu item Quick MenuEN-28 Image menu Advanced MenuEN-30 EN-31 Signal menu UserTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the tone of white Color TempAdjusting projected images About color temperatureColor Enhancer How to adjust the computer image YESTo adjust the vertical position Simple method to adjust the image positionTo adjust the horizontal position LPF Progressive filterAdvanced features Setting procedureTo enable the password function Advanced featuresPassword function To cancel the password functionPicture in Picture PinP Magnifying the displayed imageFreeze Operation Mouse remote controlProjector + computer with USB connector UP buttonSupervising and controlling by computer Major functionsConnection Indicators Normal conditionAbnormal condition Interval of lamp replacement Replacing the lampReset of the lamp operation time Replacing the lampTo replace the lamp Cleaning of the lens MaintenanceCleaning of the projector and the ventilation slots When removing the lamp from the ceiling-mounted projectorTroubleshooting No image appears on the screen Problem SolutionTroubleshooting Images are not displayed correctly Problem SolutionOthers Problem Solution EN-49 Specifications Replacement part option/not included in the boxSpecifications XGA85Connectors Dimension drawings unit mmWithout terminal cover Mitsubishielectric Corporation
Related manuals
Manual 17 pages 20.86 Kb