Mitsubishi Electronics HC900 Connecting to a Video player, etc, Connecting to a DVD player

Page 13

Connecting to a Video player, etc.

Video player, or the like

1. Connect one end (yellow) of the supplied audio/video cable to the VIDEO terminal of the projector.

ENGLISH

To audio

3

output

terminals

To video

4

output

terminal

 

COMPONENT VIDEO IN

 

To VIDEO

Audio/video

1 terminal

cable

To audio input

 

2 terminals

 

2.Connect one end (white and red) of the supplied audio/ video cable to the audio input terminals (L/MONO, R) of the projector.

3.Connect the other end (yellow) of the audio/video cable to the video output terminal of the video equipment.

4.Connect the other end (white and red) of the audio/video cable to the audio output terminals (L, R) of the video equipment.

Video player, or the like

S-video cable

To S-video output terminal

1 To S-VIDEO

2

To audio

terminal

output

 

terminals

 

4

COMPONENT VIDEO IN

 

Audio cable

3 (Option)

To audio input terminals

When the video equipment is equipped with the S- video output terminal, make the connection as follows.

1.Connect one end of the supplied S-video cable to the S- VIDEO terminal of the projector.

2.Connect the other end of the S-video cable to the S-video output terminal of the video equipment.

3.Connect one end (white and red) of an audio cable to the audio input terminals (L/MONO, R) of the projector.

4.Connect the other end (white and red) of the audio cable to the audio output terminals (L, R) of the video equip- ment.

•Also read the instruction manual of the equipment to be connected.

•Contact your dealer for details of connection.

When a TV tuner or VCR is connected:

When you use this projector with a TV tuner or VCR connected, no image may appear or a message of No Signal may appear on the screen when you change the channel via any channel that is not being received. In such a case, set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip function (that is a function not to display channels that are not being received) enabled.

Connecting to a DVD player

To connect this projector to video equipment that has component video output terminals, such as a DVD player, use the COMPONENT terminals.

Component

PB/CB

cable (Option)

PR/CR

Y

COMPONENT VIDEO IN

 

 

 

 

To audio output

Audio cable (Option)

 

 

 

 

PR/CR PB/CB

Y

terminal

 

 

 

To audio input terminal

DVD player

•Images may not be projected correctly depending on the type of the DVD player you use.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

EN-13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents HC900 Compliance Notice When using the projector in EuropeContents Important safeguards Never remove the cabinet Place of installationDo not modify this equipment Do not block the air inlet and outlet grillesPreparating your projector Checking accessoriesInserting the batteries into the remote ControlControl area OverviewTerminal panel ButtonUsing the picture quality adjusting buttons Remote controlAdjustment foot Front Lamp cover Adjustment feet Rear Preparating your projector ContinueOperational range of the remote control Using the remote controlReception angle Setting up the screen Setting up your projectorBasic setup Adjusting the projection angleScreen size and projection distance When the aspect ratio of the screen isViewing video images Connecting the projector to video equipmentBasic home theater system connection PreparationsConnecting to a DVD player Connecting to a Video player, etcWhen a TV tuner or VCR is connected Connecting to video equipment having a DVI-D terminal Plugging in the power cordViewing video images Preparation Projecting imagesTo stop projecting When projected images are distorted to a trapezoidCineFocus button How to change the settings Setting the aspect ratioWith the remote control With the Feature menuPlugging the power cord Connecting the projector to a computerViewing computer images For digital connectionEN-19 Example of the setting procedure for external output When connecting to a notebook computerViewing computer images Auto Position buttonMenu operation How to set the menusInstallation menu Available settings in the menusMenu operation Image menuSignal Menu Feature menuTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessAbout color temperature To adjust the tone of white Color TempTo enable the stored color temperature To adjust the vertical position Adjusting projected imagesLPF Progressive filter Password function Advanced featuresTo enable the password function To cancel the password functionInstallation other device’s remote commands Advanced featuresHow to install How to use the installed functionsDimension Drawings unit mm Asking for installationReplacing the lamp Interval of lamp replacementCleaning of the projector and the ventilation slots MaintenanceCleaning of the lens Reset of the lamp operation timeNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem SolutionOthers Problem Solution TroubleshootingTemperature Normal condition IndicatorsAbnormal condition Status ConditionReplacement part Option / Not included in the box SpecificationsDVI-D Hdcp ConnectorsNorth America Mitsubishi Projector Contact Information
Top Page Image Contents